Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Tool and Workbench Height

Posts

Tool and Workbench Height

#1

Tool and Workbench Height

Robby Wright - San Marcos, CA

As I get older, I am noticing that my back is hurting more when working on projects. Thinking about my last workshop session, I felt like I was bending over a lot to cut things on the table saw and working at my workbench. My workbench is at 34 inches high and I think my table saw is at 32". I will have to pay attention to whether I am bending over to reach or to see better.

I am fairly short, 5' 8" in the morning, less at night, and have short arms. My workbench is right at the height of my hands when standing next to it, but I feel like I am always hunching over. Based on this, I am thinking about raising my table saw and workbench a couple of inches. I don't do a lot of handplaning, which is reason I have heard for putting my workbench at the height it is.

I hope this makes some sense. For those with back issues, how do you handle the issue of workbench and tool height?

Re: Tool and Workbench Height

#2

Re: Tool and Workbench Height

Barry Irby

I am also about 5'8", on a good day. I don't have a problem with my back yet, but I have a couple of observations. As a builder and someone that worked his way through college building kitchen cabinets, I learned a little something about ergonomics, or thought I did. I was taught that for a cook the work surface should be at about the height your knuckles would rest on comfortably, and that's about thirty inches, or table height for women, who are generally shorter than the tall half of the male population. Since "men" designed kitchen cabinets they got standardized at 36", too tall for most women. Dishwashers and other under cabinet appliances make it difficult to lower them now, and women are getting taller.

The idea is that you should be able to do the task without bending over and without bunching up your shoulders.

I don't know what the height of my table saw is, but in my tiny shop I had my planer set so that the outfeed on my planer went under the wing on one side. I raised the planer to make the top of it level with my bandsaw table so it could serve as an out feed table. Had to raise the table saw to let the lumber from the planer go under it. Raised it 1 1/2". At first it Seemed to be about six inches higher. I adjusted to the new height and now it seems normal. Can't say that it hurt or helped, but I think its a bit better.

Never have understood why tablesaws are low and look like aircraft carriers and Bandsaws are about shoulder high and the table is the size of a dime.

Re: Tool and Workbench Height

#4

Re: Tool and Workbench Height

Chris

Robby,

By all means experiment with a higher workbench by putting your bench legs up on 2x material.

I don't have the best back. The two things I have done that have given me the most improvement have been:

1. Raising the work when handsawing.

2. Getting a wooden floor in my shop.

Good luck!

Re: Tool and Workbench Height

#5

Re: Tool and Workbench Height

Robert Fuller

Go to an orthopedic surgeon and ask to have ur legs shortened a couple inches.

Re: Tool and Workbench Height

#6

Re: Tool and Workbench Height

Robbuy Wright - San Marcos, CA

Ouch, Robert! Not sure I want to go that far!

Re: Tool and Workbench Height

#7

Re: Tool and Workbench Height

Robbuy Wright - San Marcos, CA

Barry - That is kind of what my saw is like. When thinking about it, I worry that if I raise the saw, I may have problems reaching while sawing, but I'm not really sure. I guess I will have to experiment. Thanks for your input.

Re: Tool and Workbench Height

#8

Re: Tool and Workbench Height

Robbuy Wright - San Marcos, CA

Chris - the 2x idea is what I was planning to do. I definitely don't want to remake the trestle that holds up my workbench top. Thanks for your input.

Re: Tool and Workbench Height

#9

Re: Tool and Workbench Height

Tom

I'm 74 inches, and I don't have a bench much higher than you do. I think the single most overlooked feature for a workbench is adjustable height. That would be a far better use of all the effort one sees in stuff like the benchcrafted, than what they did with their time. The adjustabench is nice, but as far as I can see, it depends on lifting the bench to it's various heights, which is OK for the young, and those with benches of modest weight. Of course a jack could be used. There are other adjustable designs, but nothing that has caught on.

Re: Tool and Workbench Height

#10

Re: Tool and Workbench Height

Barry Irby

For me going to the shop is like going to the gym for some people. My shop is way too small and working in it has a feeling of doing light calisthenics. I bend over to reach the switch and blast gate on the TS and reach as high as I can for the gate on the planer. I twist and turn to get around whatever the project is and the tools laying around. While it is exasperating, I think its good in a way.

I measured my TS after I posted my response and its now 34" tall. About five years ago when it was closer to 32" I sawed Stickers to use between some walnut we were harvesting. To combat the boredom I did the math and figured I ran a mile of stuff across the saw. It took days off and on. Don't recall any back issues. Have not had any issues since raising it, but I have grown to like it but I am not sure why.

I have a concrete floor. Someone posted they thought the wooden floor was an improvement. I have never had a shop with a wooden floor and I am something of a skeptic. Just can't imagine that a really solid wooden floor would be noticeably better, but it might. the idea is that it absorbs some of the impact from your foot better than concrete. (?????) I do believe excellent shoes would be good and a wooden floor might be warmer under foot. Soft rubber pads at your work stations would be good.