Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Samantha's dresser 7- case assembly

Posts

Samantha's dresser 7- case assembly

#1

Samantha's dresser 7- case assembly

Bill Tindall, E.Tn.

Assembly of the case

PIC1


The picture shows some of the 30 pieces that must be fit together to make the case. An initial dry fit of them all ensures that when the glue is applied the case will assemble stress-free. Some are successful gluing up case work in subassemblies first. I am not. To ensure the final case winds up square I like it all to go together at one time.

I use liquid hide glue for things that slide together. This glue lubricates the joint enabling the joint to slide together in a controlled manner. This glue also has a long working time. With the case sides on edge on the bench I install all the dividers on the back side- top divider, bottom divider and then fill in the rest. If you don’t have a helper a clamp like what was used to hold the boards to the bench for dovetail sawing (wooden hand screw) works just dandy for holding the sides upright on the bench. Then flip the case, add the runners and then install the dividers on the front side. At this point err on not having the dividers pressed in far enough for they are not easily retracted. The problem of proud dividers is easily cured later (see below). Then I set the case upright and inspect that the dividers are flush with the front and back side. If they are proud a bit, and some usually are, I squish them into position with a clamp across the case side. Finally the false top is installed.

It may be of interest here to describe the two “glue times” that are relevant to this assembly. “Open time” is the maximum amount of time the glue applied to the open joint can be exposed to air before its surface hardens and interferes with proper bonding. This time depends on temperature and humidity as well as glue type. “Closed time” is the time after the joint is assembled that the joint can be coaxed into position. This time depends on glue type, temperature and moisture content of the wood. This time is typically longer than open time. Fifteen minutes is a typical closed time.

The glues we use have low shear strength before curing. Coaxing a joint into position is best done with steady clamp pressure. Bashing is futile once the bond begins to cure, while clamp coaxing usually saves the day.

Using the construction described, namely dovetailed dividers and a dovetailed top, there is nothing to clamp. However it goes together is how it will be. If the dovetails on the ends of the dividers were square the case must be square. The handy jig shown previously ensures this is the case. After assembly I measured the diagonals and they were within 1/32”. I was pleased. Square makes drawer fitting a breeze.

Note, it sits on a platform with casters. I find this arrangement handy for working on it. I can easily wheel it to whatever position required, or out of the way.

Also note the dovetails are now covered up. The next installment will cover that operation. The lumber sticking out of the drawer openings are drawer parts. It is handy place to store parts.


Re: Samantha's dresser 7- case assembly

#2

Beekeeper, you should count your bees

Barry Irby

or drawers, one of them is missing. :)

Looks good. I was wondering about the front edge of the yellow pine, but I see you have covered that as well. Obviously you are not concerned about the differential in the expansion and contraction of the walnut versus the pine? It would worry me on a piece 17" wide. You know better?

Your drawer runners. Are they on the surface or are they housed in the slot for extra support. Do you pin them to the front stretcher so the movement takes place at the rear only?

Do you sand the inside of the case? I have one drawer in the chest I am working on that has what feels like a little friction. Today is the day to seek the problem. I was wondering if sanding will help or perhaps sanding, Shellac and wax? Might have been a good idea to sand the inside of the case.

I had a cart like that. My shop floor is a little rough. Wheels that small would practically lock up if you ran over a shaving. Bigger wheels roll better.

Re: Samantha's dresser 7- case assembly

#3

Re: Beekeeper, you should count your bees

William Duffield, on the Cohansey

I can empathize with your comments on wimpy wheels. I have an incompetently designed Ridgid shopvac whose wheels (probably cost reduced by some idiot) are too small to roll over its own electrical cord. That sort of annoyance is never a problem with my Festool Vacs, even though they have much thicker, more robust cords.

Re: Samantha's dresser 7- case assembly

#4

check the hive

Bill Tindall, E.Tn.

all parts are not resawn yet

Obviously you are not concerned about the differential in the expansion and contraction of the walnut versus the pine? ....No,This is common construction in Period VA, NC, SC furniture

Your drawer runners. .....the pictures of making and installing surely illustrate how they go together. I am still thinking about the pining of runner situation.

Do you sand the inside of the case? no, I do shellac and wax.

Wheels that small .....the wheels are 3" urethane and work fine.

Re: Samantha's dresser 7- case assembly

#5

Re: Samantha's dresser 7- case assembly

William Duffield, on the Cohansey

Back in the "good old days" of air dried lumber, it seems that the loose tenons supported by the back rails were usually a lot longer (and the mortises deeper), so that when the sides expanded in the summer, the runners didn't drop out, or when they shrank in the winter, the runners didn't push the drawer blades out of the carcass. Do you see any potential problems in your climate or with the kiln dried lumber you prefer?

Re: Samantha's dresser 7- case assembly

#6

not a problem

Bill Tindall, E.Tn.

The 18" case side is going to have to expand more than 5/8" for the runners to drop out.

As I have stated before, the "shrinkage" tables greatly overestimate lumber dimension changes based on actualy data collected over the past several years in my living conditions.

Stay tuned for the results of some interesting data on the effect of finish on moisture transport rate as well as changes at the end of a board vs the middle.