Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Drill Chuck Question Follow up

Posts

Drill Chuck Question Follow up

#1

Drill Chuck Question Follow up

Barry Irby

Three days ago I posted a question about how t tighten the chuck on a little Bosch L-ion drill. I was a little embarrassed to discover that choking the chuck in one hand and spinning the motor with the other on the switch might not be the best way to do it and that you can tighten it better by hand. Apparently the shaft locks when the drill stops and you can really cinch down on it even when the clutch is set to one of the low settings. Originally, I thought the problem was that the drill stops so suddenly that it was impacting the chuck loose.

Well, yesterday I was using it again to drill a few hoes for my Kreg Jig and then drive the screws. I put the bit in the chuck and spun it home and then cinched it by hand. In the process of drilling about ten holes it came loose. I put a hex shank square drive bit in it and drove the screws. Again, tightening the bit as tight and I could. Somewhere in the process of gently drive the screws, the bit fell out and I was not running the drill any where near full speed.

I think I need a different Chuck. I have not heard from Bosch.

Re: Drill Chuck Question Follow up

#2

Ridgid Drill?

Bill Tindall, E.Tn.

I don't know why this company doesn't own the market, given their guaranteed for life battery replacement policy. Even the Li ion batteries are going to die in a few years (about 3 in my hands). And when they die replacement is about the cost of a new drill. Owning the Ridgid has been like avoiding buying a new drill every few years.

Re: Drill Chuck Question Follow up

#3

Re: Drill Chuck Question Follow up *LINK*

Lars Parrington

As I said in the other thread, it's pretty easy to upgrade the chuck. There are at least a few good candidates on ebay right now. Here's one example:


http://www.ebay.com/itm/DeWalt-Rohm-Keyless-1-2-Metal-Chuck-With-Screw-330075-91-330075-45-/251401817205?pt=LH_DefaultDomain_0&hash=item3a88b74c75

Re: Drill Chuck Question Follow up

#4

Re: Drill Chuck Question Follow up

Dick Coers

Just as a side note, Kreg fixtures work so much better with a corded drill. The higher rpms make the bit work better with chip ejection, and it's way, way faster! They used to insist on that, but with TV hosts using cordless, and folks resistant to plug in a cord, I don't know if they still do.

Just had the thought that maybe you should choose another joinery method. First you destroyed a jig, now the drill won't hold a bit. It's not supposed to be that tough Barry.

Re: Drill Chuck Question Follow up

#5

I repaired the Kreg Jig.....

Barry Irby

Used Loctite retaining compound and it seems to have worked. This was the first use.

I usually use a corded drill for this. I have a decrepit old Dewalt drill I have grown to hate and I was trying to run it to death as an excuse to get a new one. I finally killed it and I'm too broke to get a new one. Now I am considering rebuilding it. :(

I have been feeling Like the little guy in the funny papers with the cloud over his head. Time for something good to happen.

I will keep struggling with this crappy chuck until I am driven to distraction and then I will do SOMETHING.

Re: Drill Chuck Question Follow up

#6

Re: Drill Chuck Question Follow up

pecker

My Porter cable drill does the same thing. I think somehow the single handed tightening feature combined with what happens when the clutch disengages cause the chuck to self loosen. It is worse when using bits that have the 1/4" hex shank than with round drill bits.

Re: Drill Chuck Question Follow up

#7

Kneale Brownson

Joe Btfsplk

Kneale Brownson


Re: Drill Chuck Question Follow up

#8

Re: Joe Btfsplk

mdclor

Wow!! I don't think I have seen Joe in 40 years. lol

Re: Drill Chuck Question Follow up

#9

Re: Drill Chuck Question Follow up

Barry Irby

I found the same thing with the hex shaft driver bit, It just fell out. The drill bits loosened, but not quit as badly.

My son suggested a drill with a hex driver and just by a set of hex shank bits. OK but limiting.