Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Durable Table Top Finish Suggestions?

Posts

Durable Table Top Finish Suggestions?

#1

Bart Goldberg

Durable Table Top Finish Suggestions?

Bart Goldberg

I'm helping my son build a table for his equipment/computers. I am looking for suggestion on a fairly durable, non-spray type, finishing product. Any suggestions? I have some General Finishes water based poly I've used before, but looking for other suggestions.

Thanks

Bart

Re: Durable Table Top Finish Suggestions?

#2

Ellis Walentine

Durability

Ellis Walentine

If it's only durability that matters, and if spraying is out, a water-borne polyurethane is probably a good choice. High-end floor finishers use catalyzed water-borne polyurethane all the time, and that has to stand up to foot traffic. I don't have comparative abrasion-resistance data for the various products out there, but I'd say any of them would be acceptable if not superior for this application. Oil-based polyurethanes are another option.

Ellis

Re: Durable Table Top Finish Suggestions?

#3

Re: Durable Table Top Finish Suggestions?

David Yoho

I agree with what Ellis said. Either water-borne polyurethane or oil-based would be fine. It's a matter of what you are comfortable with. Some water-borne polyurethanes can look cold. If that's a problem you're trying to avoid, then use the oil-based.

Re: Durable Table Top Finish Suggestions?

#4

Re: Durable Table Top Finish Suggestions?

Howard Acheson

Moving desktop computers around on a table top is going to abrade of scratch the surface. I made a computer work bench for a semi-pro computer technician and we used Formica. It's held up well.

I don't think any brush on or spray on finish will prove durable for someone who works on computers. At the very least, a mat covering would provide protection.

Re: Durable Table Top Finish Suggestions?

#5

dry time is different than cure time

Dick Coers

The most overlooked information on water based poly is the cure time. Check with General since we don't know exactly what material you are using, but some full cure times to full hardness may be weeks after you apply it. I can't find anything on their website about curing time. Remember, they also have professional finishes if you are not using them.

Re: Durable Table Top Finish Suggestions?

#6

JL

Re: Durable Table Top Finish Suggestions?

JL

Behlen's Rock Hard - if he isn't going to be moving it around.

Re: Durable Table Top Finish Suggestions?

#7

floor finish

Bill Tindall, E.Tn.

A solvent based urethane will be durable. It will be scuff resistant and moisture resistant enough that it can be washed as needed. When faced with this problem I visit the stores and see if I can dent with a finger nail the test piece they usually have on display. The better finishes will not dent much or any.

For better brushing, thin it 1 part solvent to about 3 parts (depending on temperature) varnish. Thin enough that it flows and levels quickly. Test on a test board. Coat, let cure, sand smooth, coat again. then rub out with 4/0 steel wool and wax.

Re: Durable Table Top Finish Suggestions?

#8

Clint Searl

Bona Mega floor finish


Re: Durable Table Top Finish Suggestions?

#9

Re: Durable Table Top Finish Suggestions?

Howard Acheson

>>>> Behlen's Rock Hard - if he isn't going to be moving it around.

Have you tried the new Behlen's Rockhard? In the past year they have changed their formulation to a poly resin product. It's no longer a non-poly finish.

Re: Durable Table Top Finish Suggestions?

#10

Bart Goldberg

Re: Durable Table Top Finish Suggestions?

Bart Goldberg

Thanks for all the replies. I have two different General Finishes water based poly products: High Performance that I've used on cabinets before, and Enduro Var. I think for this table, I'll go with the Enduro Var as its a bit more durable, according to their web site.

Thanks

Bart

Re: Durable Table Top Finish Suggestions?

#11

Kick'em Up

Mark Mandell - Gone Round In New Jersey

to a higher wear level by adding General's cross-linker to either your HP Poly or the EnduroVar.

Pricey ($35/pt) but worth it for table surfaces.

Re: Durable Table Top Finish Suggestions?

#12

Bart Goldberg

Re: Kick'em Up

Bart Goldberg

Mark, According to the General Finishes site, they are saying to not add cross-linker cause its already included in the Enduro Var formula.

Bart

Re: Durable Table Top Finish Suggestions?

#13

They Make The Stuff

Mark Mandell - Gone Round In New Jersey

follow their directions :D