Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Bandsaw Blade Drift

Posts

Bandsaw Blade Drift

#1

Bandsaw Blade Drift

Don Emmerling

Hi Folks,

I have a Jet 18" bandsaw and I was trying to resaw a piece of 1" walnut to 3/8" for another project. The board was about 6 or so inched in width. I used a marking gauge to scribe the line to follow on the saw. I started out using the fence to guide the cut but realized about halfway through that I was getting a bit of drift and could not stay on the line. I moved the fence out of the way and continued to cut to the line by slightly angling the board. I was cutting very slow with just a gentle push to run the board through the saw. I believe the bandsaw blade is a bit dull but at least on other cuts it seems to do well. After sawing the board through I noticed that despite staying on the line at the top the bottom part of the cut had drifted so that I essentially was cutting on a diagonal. While at the top of the board it was 3/8" and at the bottom it was more like 1/4". I have had this happen before on resawing efforts. The blade tension seems good. I also noted that the diagonal like cut seemed to start approximately halfway through the resaw, coincidentally or not when I started to cut freehand, that is without the fence. I am not quite sure what is causing this. I see youtube videos of resawing and they always just seem to buzz right through the effort and everything is square. Any thoughts out there in woodland?

Re: Bandsaw Blade Drift

#2

Re: Bandsaw Blade Drift

Mark Nowicki

Ever since I followed his instructions, my old 14" Delta has no drift whatsoever.

My saw has old tires, old bearings, and a blade on which I have not released the tension in years.

http://www.youtube.com/watch?v=wGbZqWac0jU

Re: Bandsaw Blade Drift

#3

Re: Bandsaw Blade Drift

paul in AZ

I have a jet 18" and have encountered resaw troubles on occasion. Sometimes ordinary linear drift and on one occasion with a rock hard African wood the drift was in the middle of the width -making a concave cut.

I know how to make all the mistakes.

Aside from tension error or overly aggressive feed the reason for drift IS a dull blade IMO. A worn blade can seem to work just fine in boards of up to a couple of inches but do not-so-nice things when resawing.

Your mention of the blade being "a bit dull" could be one answer.

Re: Bandsaw Blade Drift

#4

Re: Bandsaw Blade Drift

Dick Coers

Your blade is a "bit dull" and your tension is "about right", so you get a resaw cut that is a "bit about right". Get a new blade, then tension till it cuts right. Then you will get the cut you want. Many people expect to get the life out of a band saw blade that compares to their table saw blade. Not even close. If you need to, keep a blade for just resawing and use that "a bit dull" blade for 1" thick cutting.

Re: Bandsaw Blade Drift

#5

Ellis Walentine

Lotta issues here

Ellis Walentine

You've characterized the problem as drift, which occurs when the blade wants to cut to one side or the other of the line. Many newer bandsaws come with an adjustable fence that allows you to correct for the skewed trajectory. A lot of folks make up a right-angle fence made from plywood and set it at whatever angle compensates for the drift. That might be something you'd want to consider, especially if you're used to conventional fences. Be sure that whatever fence you use is tall enough to register the workpiece.

In my opinion, drift is primarily an issue with the blade. If the tooth set is off to one side or the other, or there has been a dulling incident on one side or the other, the blade will want to cut more aggressively to the sharper side, twisting the blade in the kerf as it cuts, and leading the blade away from a straight cut.

Your question about the diagonal cutting probably has to do with the fact that you took the fence away when you noticed the drift. Trying to feed your workpiece without benefit of any perpendicular reference surface invites this sort of problem. A point fence, or a bowed fence as Mark Duginske prefers, enables you to correct for drift in real time, while keeping your workpiece at right angles to the table.

The next suspect here is the blade you're using. For resawing, I've never used any blade with more than three teeth per inch, except on fairly narrow resawing tasks. More than that, and you're going to clog up the kerf with dust and cause the blade to deflect backwards in an arc, and the narrower the blade the worse the deflection. This deflection is what causes the scooped cuts that Paul mentioned. It's sorta like the old example of a small length difference in a railroad track leading to a huge swing in its path. I wish someone would post the evidence of this.

To complicate things, I've seen reports that faster feed speeds lead to better resawing performance, but you can't cut faster if your blade is dull.

So there you are. My recommendation is to try a new blade that is sharp and matched better to the task. Stretch it tight (you didn't mention how you determined your blade was properly tensioned) and conduct some drift tests before you proceed to your actual workpiece. Adjust your fence to the drift angle, or use a point- or bowed fence and monitor the line as you cut.

Ellis