Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

(OT) Replacing vehicle's radio antenna

Posts

(OT) Replacing vehicle's radio antenna

#1

(OT) Replacing vehicle's radio antenna

Dan

the radio antenna on my 2000 Ford Ranger XLT snapped off a week or so ago. I was told at a car audio place it would be better to do it myself because they just "screw in and out". that may be so, but mine was an aftermarket item (not the factory antenna) so I'm not sure the threads will match if I can get to them.

I did some google searching a few days ago and one of the pages I went to said to pry off the escutcheon plate, which I tried a little bit but couldn't budge it. Not being familiar with such things, I didn't want to do more damage. anyone familiar with how this might be accomplished?

I'm hoping I can just replace the mast and not have to fish a new wire all the way to the radio. To that end, can the wires (old antenna and new one) be spliced together?

I'd post a picture, but I don't see how to do it unless it's on a web site (it's not).

Thanks for any input you might provide. DB

Re: (OT) Replacing vehicle's radio antenna

#2

Re: (OT) Replacing vehicle's radio antenna

John McGaw

I take it that this is a fixed, not power, antenna? How far down is it broken? Many antenna masts, the non-power variety, literally do just unscrew from the top of the insulator and once a mast is unscrewed it should be simple to measure the thread and figure out some sort of replacement. Splicing the cable is definitely not a good thing to do -- vehicle antennas are touchy and are working in a bad noise environment with weak signals and any discontinuity in the cable is going to do nasty things.

BTW: is the antenna assembly in a location where the underbits are accessed from inside the vehicle or from outside under the fender? This means a lot if a full replacement is called for.

Re: (OT) Replacing vehicle's radio antenna

#3

Re: (OT) Replacing vehicle's radio antenna

Dan

Sorry, should have mentioned it was a fixed antenna. The think whippy part of the antenna dropped down to a larger roundish "bulb". It broke off flush with the "bulb." There are no flat spots on the "bulb" that might be used for gripping with pliers, etc. It's sort of hard to describe. There is a picture posted at another WW side that sits by a meandering stream.

Thanks for the heads up about splicing.

Re: (OT) Replacing vehicle's radio antenna

#4

Re: (OT) Replacing vehicle's radio antenna

el schisler

i put in lot's of car antenna's , if i remember if you get the other one out , the new one goes in from the out side , just get a new one , if you can find one complete, may have to do ebay ? their is a piece that is a 1/2 moon on the antenna that you turn and it makes it the same size so it will go thro the hole, now that piece will swing open or move so that the antenna will now come back the hole, not the nut will go over and screw the antenna tight to the finder, you will have to snake the cable back thro the fire wall and plug in to the back or side of the radio , not a easy job, i used to do that back in the early 50's , good luck

Re: (OT) Replacing vehicle's radio antenna

#5

Re: (OT) Replacing vehicle's radio antenna

el schisler

a follow up i looked at ebay and found these

http://www.ebay.com/sch/i.html?_trksid=p2055845.m570.l1311.R10.TR12.TRC2.A0.Xcar+radio+antenna&_nkw=universal+car+radio+antenna&_sacat=0&_from=R40

Re: (OT) Replacing vehicle's radio antenna

#6

Re: (OT) Replacing vehicle's radio antenna

Dan

Thanks. I'm hoping not to have to fool with pulling a wire if I can avoid it. That's why I went to the car audio place to start. I figured they could do it in less than half the time I could with way fewer headaches since that's what they do. But he sent me away. I may try him, or another store like it if there's one in town, if I can't figure it out. DB

Re: (OT) Replacing vehicle's radio antenna

#8

Don't remove the old one without...

Tom Dunlap

...attaching a piece of shoelace or something like that to the old coax to snake the new coax back through. I girth hitch and tape the cord in a case like this.

If you don't you're in for a LOT of work and frustration.

Tom

Re: (OT) Replacing vehicle's radio antenna

#9

Re: Here are some instructions

Dan

Thanks. That will be helpful. DB

Re: (OT) Replacing vehicle's radio antenna

#10

Re: Don't remove the old one without...

Dan

For sure! You're not the first one to remind me of that. Thanks. DB