A new timber tech book. Would you buy it?
Sgian Dubh
This is to try and establish what interest there may be in the forum users here in buying a new book on timber technology. The story, briefly, is that in about 2005 I started creating illustrated texts on the subject with the idea that they could be used as learning aids for the students I teach, as well as perhaps becoming published articles in woodworking magazines. For one reason or another as the text grew I decided I didn’t wish to go down the magazine article route, and the text had grown substantial enough that it would probably best suit a book format. Additionally, once I'd decided to go down the book route, as I was writing I considered how it might be seen when judged against Hoadley's Understanding Wood, a commonly recommended text on the subject. Hoadley's book is very good, but there are parts of it that are dense and without, I believe, adequate explanation of essentials or primary knowledge that would make the text more accessible, and I have tried to address that, and to cover several subjects that he doesn't.
Anyway, eventually the manuscript was finished in June this year and it’s being considered for publication by the Timber Research and Development Association (TRADA) here in the UK. TRADA seem to be genuinely interested in publishing my manuscript but are expressing some concern about how much they would have to charge, and how many woodworkers, professional, amateur, and others would buy it for them to make a profit on the venture. The manuscript is large I admit, covers a lot of ground, and has a great many images, and the impression I’m getting is that they are thinking the price of the finished book could be in the region of £35- £50, which might seem quite a bit, but over a year that's less than a pound a week. I'm guessing, but the price in the US might be about £40- $55.
The question is therefore, would you be willing to pay this sort of amount for a book on this subject, a subject that I believe is very important in our endeavours as woodworkers? If I could get some feedback and it’s generally positive, i.e., "Yes, I think I'd buy it", I can pass this back to TRADA, and that might be just enough to help persuade them to go ahead and publish. To help you make up your mind I have attached a synopsis of the text along with the manuscript’s Table of Contents below my signature.
Thanks in advance for your consideration and feedback, and apologies for the long post. Slainte.
________________________________________
Synopsis for
Trees, Wood and Woodworking:
Wood Know-How for the Woodworker
by
Richard Jones
________________________________________
Trees, Wood and Woodworking is an academically referenced and peer reviewed manuscript on timber technology written by a woodworker for other woodworkers. Most books on wood science are a challenging read because the subject can be very involved and highly complex, and this is surely because almost all the authors are timber technologists writing mostly for their fellow wood scientists or students of the subject. The primary driver for writing the manuscript was to create a text for an international readership that makes timber technology accessible to those without a scientific background, but perhaps with some knowledge of the subject through being an existing professional woodworker, or for those beginning a career in woodworking, along with catering for amateur woodworkers and even the general reader with an interest in the field. Significant effort has been expended to find ways to explain those elements of the subject that are especially challenging through, for example, such means as analogies, explanation of terminology and technical terms where required, and clear examples used in various formulae and calculations.
Core subjects include the physiology of trees, their worldwide distribution; tree felling, calculating log yield, log conversion, seasoning methods and drying faults. The subjects of water and wood along with wood movement and stability are discussed with sample calculations for wood expansion and contraction, along with appearance grading and strength grading, as well as fungi and wood, and insect pests and wood. Characteristics of timber are outlined, e.g., figure, texture, knots, shakes, et cetera, along with issues relating to wood strength and its use in structures and concluding with a section on ecological and environmental issues relating to trees, forests, wood use, et cetera. In addition to tackling these core topics the text also looks briefly at such subjects as socio-political issues, balanoculture, ancient trees and forests, deforestation in antiquity, the effect of The Black Death on forest regeneration in Europe, et cetera, with the purpose of rounding out a woodworker’s knowledge in the subject, supplemented by links through quotations and the bibliography to further reading.
The text, in its current draft form, is illustrated with approximately 300 photographs and 120 figures (tables, charts, sketches, et cetera), and, including the bibliography, glossary, index, et cetera, the word count amounts to a little over 170,000.
Please see the Table of Contents below listing all the subjects covered.
Table of Contents
Table of Figures______________________________________________________ 9
Acknowledgements__________________________________________________ 14
Foreword_________________________________________________________ 16
Section 1 Introduction________________________________________________ 18
1.1 The Ubiquitous Oak______________________________________________ 21
1.2 Balanoculture___________________________________________________ 24
1.3 Oak: Partner of Mankind_________________________________________ 26
1.4 United Kingdom of Great Britain Tree Cover_________________________ 30
1.5 The Romans and Later Centuries___________________________________ 31
Religion, Forests and Ancient Trees_________________________________ 33
1.6 The ‘Baltic Problem’______________________________________________ 33
1.7 Tree History, Oddities, and Tree Migrations__________________________ 35
The Wollemi Pine________________________________________________ 36
1.8 The Latin Binomial System________________________________________ 39
Section 1 References_________________________________________________ 42
Section 2. Tree Distribution___________________________________________ 44
2.1 Equatorial rainforest_____________________________________________ 44
2.2 Montane Tropics________________________________________________ 44
2.3 Monsoon Forest_________________________________________________ 45
2.4 Savannah and Desert____________________________________________ 45
2.5 Mediterranean Forest_____________________________________________ 46
2.6 Temperate Forest________________________________________________ 46
2.7 Boreal Forest and the Taiga________________________________________ 46
2.8 Tundra________________________________________________________ 46
Section 3. Tree Classification, Growth and Structure._____________________ 48
3.1 Log Cross Section._______________________________________________ 51
3.2 Gymnosperms and Angiosperms- Essential Differences_________________ 54
3.2.1 Gymnosperms.______________________________________________ 54
3.2.2 Angiosperms._______________________________________________ 55
Section 3 References_________________________________________________ 55
Section 4. Roots, Leaves, Seeds, Flowers, Germination, Transpiration, Woodland Regeneration 56
4.1 Roots._________________________________________________________ 56
4.2 Buds.__________________________________________________________ 62
4.3 Leaves.________________________________________________________ 64
4.4 Flowers._______________________________________________________ 66
4.5 Seeds and Germination___________________________________________ 68
4.5.1 Acorn Distribution__________________________________________ 70
4.6 Transpirational Pull and Root Pressure______________________________ 72
4.7 Woodland Regeneration__________________________________________ 74
4.8 Characteristics Found in Deciduous Trees____________________________ 75
Section 4 References_________________________________________________ 78
Section 5. Felling, Conversion and Yield________________________________ 79
5.1 Viable wood for conversion._______________________________________ 79
5.1 Felling, Logging, Harvesting_______________________________________ 83
5.2 Conversion of Wood_____________________________________________ 87
5.2.1 Typical sawing sequence of sawlogs in North America.____________ 93
5.2.1.1 A Round-Up of Selected Sawmills__________________________ 94
5.2.1.2 Nidd Valley Saw Mills Photo Essay_________________________ 95
5.2.1.3 Bandsaw Blade Maintenance at Nidd Valley Saw Mill_________ 96
5.3 Measuring Log Yield_____________________________________________ 96
5.4 Hoppus Feet____________________________________________________ 99
5.5 Doyle Scale_____________________________________________________ 99
Section 5 References________________________________________________ 102
Section 6. Water, Water Vapour and Wood_____________________________ 103
6.1 Atmospheric Humidity__________________________________________ 103
6.2 Water in Wood.________________________________________________ 108
6.3 Hysteresis_____________________________________________________ 113
6.4 Moisture Gain and Loss in Wood- An Analogy.______________________ 113
6.5 Fibre Saturation Point___________________________________________ 114
6.6 Measuring Wood Moisture Content________________________________ 116
6.7 Microwave Oven Drying________________________________________ 119
6.8 Moisture Meters________________________________________________ 122
6.9 Green Wood Use and Chair Bodging_______________________________ 124
6.10 Wood Moisture Content Percentages and Appropriate Timber Use_____ 125
6.11 Atmospheric RH- Its Effect on Wood MC__________________________ 128
6.12 Allowing for Changes in Wood Moisture Content___________________ 132
6.12.1 Glued Edge Joint Failure During Panels Shrinkage_______________ 135
6.13 Moisture Content and Dimensional Change in Wood________________ 136
6.14 Tangential, Radial, Longitudinal Shrinkage_________________________ 139
6.15 Sapwood Movement and its Use in Projects________________________ 141
Section 6 References________________________________________________ 143
Section 7 Coping with Wood Movement: Dimensional Change, Distortion, Moisture Cycling and Stress Release (Kickback)____________________________________________ 145
7.1 Dimensional Change and Stability_________________________________ 147
7.2 Calculating Wood Movement_____________________________________ 149
7.3 Sample Wood Expansion and Contraction Calculations_______________ 150
7.4 Distortion- Warping, Cupping, Bowing, et cetera.____________________ 156
7.5 Wood Movement and Joinery_____________________________________ 160
7.6 Built Up Laminations____________________________________________ 162
7.7 End Grain Orientation and Panel Glue Ups__________________________ 163
7.8 Wide Boards___________________________________________________ 165
7.9 Chatoyance Considerations______________________________________ 165
7.10 Edge Joinery__________________________________________________ 167
7.10.1 Rub Joints and Cramping Pressure___________________________ 169
7.11 Storing a Panel Between Glue-Up and Use._________________________ 171
7.12 Mitres and Movement__________________________________________ 172
7.13 Moisture Cycling______________________________________________ 173
7.14 Moisture Cycling in Table and Cabinet Tops________________________ 174
7.15 Water Damage: Surface Checking and Cupping_____________________ 175
7.16 Stress Release in Wood During Ripping Operations: Kickback_________ 176
Section 7 References________________________________________________ 178
Section 8 Seasoning or Drying of Wood_______________________________ 179
8.1 Drying Wood Using Air_________________________________________ 181
8.2. Wood Moisture Content in Response to Temperature and Relative Humidity 186
8.3 Stickers and Stickering___________________________________________ 188
8.4 Air Drying____________________________________________________ 192
8.5 Advanced Air Drying Methods___________________________________ 197
8.5.1 Forced Air Drying__________________________________________ 198
8.5.2 Accelerated Air Drying______________________________________ 198
8.5.3 Low Temperature Warehouse Pre-drying_______________________ 199
8.5.4 Climate Chambers__________________________________________ 199
8.6 Wood Drying Kilns_____________________________________________ 200
8.6.1 Conventional Kiln Drying___________________________________ 200
8.6.2 Dehumidification Kilns______________________________________ 201
8.6.3 Progressive Kilns___________________________________________ 202
8.6.4 Solar Kilns________________________________________________ 202
8.7 Circulating Air, Monitors and Kiln Controls_________________________ 206
8.7.1 Moving Air in Conventional and Dehumidification Kilns__________ 206
8.7.2 Vents____________________________________________________ 207
8.7.3 Supplying Heat and Steam___________________________________ 207
8.7.4 Monitoring Chamber Conditions______________________________ 209
8.7.5 Withdrawable Monitoring Samples____________________________ 210
8.7.6 Recording Devices__________________________________________ 213
8.8 Kiln Drying Schedules___________________________________________ 213
8.9 Special Kiln Treatments__________________________________________ 215
8.9.1 Equalisation_______________________________________________ 215
8.9.2 Case-hardening Relief (Conditioning)__________________________ 215
8.9.3 Collapse Repair (Core Collapse Repair)_________________________ 216
8.9.4 Steamed and High Heat Treatment of Woods___________________ 217
8.9.4.1 Steamed Wood________________________________________ 217
8.9.4.2 High Heat Treatments__________________________________ 220
8.9.5 Keeping Pests at Home______________________________________ 222
8.10 Kiln Drying Standards__________________________________________ 223
8.10.1 Target Moisture Content for Kiln Dried Wood__________________ 223
Section 8 References________________________________________________ 225
Section 9 Drying Faults______________________________________________ 227
9.1 Case-hardening and Reverse Case-hardening________________________ 229
9.2. Seasoning Induced Wood Discolouration___________________________ 232
9.2.1 White Stain in Oak_________________________________________ 232
9.2.2 Yellow Stains______________________________________________ 233
9.2.3 Metallic Stains._____________________________________________ 233
9.2.4 Dark Core in Pale Wood Species______________________________ 233
9.2.5 Water Stains_______________________________________________ 234
Section 9 References________________________________________________ 234
Section 10 From the Kiln to the User___________________________________ 235
10.1 Green or Dry Tally?____________________________________________ 239
10.2 Visual Grading of Timber (Lumber in North America)________________ 240
10.3 American Appearance Grading__________________________________ 241
10.3.1 First and Seconds Grade (FAS)_______________________________ 243
10.3.2 FAS One Face Grade (F1F)__________________________________ 243
10.3.3 F1F Grade in Cherry and Walnut_____________________________ 243
10.3.4 Selects Grade_____________________________________________ 244
10.3.5 Prime Grade and Comsel Grade______________________________ 245
10.3.6 Number 1 Common Grade (No 1C)___________________________ 245
10.3.7 Number 2 Common Grade (No 2AC)_________________________ 246
10.4 UK Appearance Grading_______________________________________ 247
10.5 Measuring Planks or Boards in the UK____________________________ 249
10.6 Appearance Grading of Oak Grown in Mainland Europe_____________ 251
10.6.1 Boules and Selected Boards: Q-B..., and Q-S... grades____________ 252
10.6.2 Strips and Square Edged Timber: Q-S... grades__________________ 254
10.6.3 Beams: Q-P... grades_______________________________________ 254
10.7 General Wood Buying Tips______________________________________ 255
Section 10 References_______________________________________________ 257
Section 11 Fungi____________________________________________________ 258
11.1 Physiology and Structure_______________________________________ 258
11.2 Beneficial Fungi_______________________________________________ 261
11.2.1 Ectomycorrhizae__________________________________________ 261
11.2.2 Endomycorrhizae_________________________________________ 261
11.2.3 Endophytic Fungi_________________________________________ 262
11.3 Unwelcome Fungi_____________________________________________ 263
11.3.1 Sap Stain________________________________________________ 264
11.3.2 Brown Rots______________________________________________ 265
11.3.3 Dry Rot: Serpula lacrymans_________________________________ 266
11.3.4 White Rots_______________________________________________ 267
11.3.5 Armillaria fungus_________________________________________ 268
11.3.6 Soft Rots_________________________________________________ 270
11.3.7 Dote or Punk_____________________________________________ 271
11.4 ‘Beautifying’ Fungi_____________________________________________ 271
11.4.1 Brown oak and Tiger oak___________________________________ 271
11.4.2 Spalting_________________________________________________ 273
11.4.3 Green Stained Timber______________________________________ 274
11.5 Health Risks of Fungi.__________________________________________ 274
Section 11 References_______________________________________________ 276
Section 12 Insect Pests_______________________________________________ 277
12.1 Termites_____________________________________________________ 277
12.1.1 Subterranean Termites_____________________________________ 279
12.1.2 Drywood Termites_________________________________________ 283
12.1.3 Dampwood Termites_______________________________________ 283
12.2 Common Furniture Beetle- Anobium punctatum____________________ 284
12.3 Death-Watch Beetle- Xestobium rufovillosum_______________________ 287
12.4 Powder Post Beetle- Lyctus Beetle_________________________________ 289
12.5 Pinhole borers- ambrosia beetles__________________________________ 290
12.6 House Longhorn Beetle- Hylotrupes______________________________ 291
12.7 Leaf-miner Flies- Pith Fleck______________________________________ 292
12.8 Carpenter Ants (Camponotus species)_____________________________ 293
12.9 Bees and Wasps_______________________________________________ 296
12.9.1 Solitary Bees______________________________________________ 296
12.9.2 Carpenter Bees____________________________________________ 297
12.9.3 Carpenter Wasps__________________________________________ 298
12.10 Insect Pest Control, Eradication, and Deterrents____________________ 298
12.10.1 Other Insect Control Methods______________________________ 301
Section 12 References_______________________________________________ 303
Section 13 Characteristics of Timber___________________________________ 306
13.1 Grain________________________________________________________ 306
13.1.1 Figure___________________________________________________ 309
13.1.2 Texture__________________________________________________ 312
13.1.3 Colour__________________________________________________ 313
13.1.4 Lustre___________________________________________________ 316
13.2 Knots- Knot Formation and Structure_____________________________ 316
13.2.1 Knot Descriptions_________________________________________ 318
13.3 Shakes_______________________________________________________ 320
13.3.1 Radial Shakes_____________________________________________ 321
13.3.2 Tangential Shakes (Ring Shakes and Cup Shakes)_______________ 321
13.3.3 Cross Shakes_____________________________________________ 322
Section 13 References_______________________________________________ 323
Section 14. Wood Strength and Structures_____________________________ 324
14.1 Frequently Tested Strength Properties_____________________________ 324
14.1.1 Compression Parallel to the Grain____________________________ 325
14.1.2 Compression Perpendicular to the Grain_______________________ 325
14.1.3 Tension Perpendicular to the Grain___________________________ 325
14.1.4 Tension Parallel With the Grain______________________________ 326
14.1.5 Shear Parallel With the Grain________________________________ 326
14.1.6 Shear Perpendicular to the Grain_____________________________ 326
14.1.7 Impact Bending___________________________________________ 327
14.1.8 Hardness________________________________________________ 327
14.1.9 Modulus of Elasticity and Modulus of Rupture__________________ 328
14.1.10 Work to Maximum Load___________________________________ 328
14.2 Rarer Strength Properties_______________________________________ 329
14.2.1 Rolling Shear-- in plywood__________________________________ 329
14.2.2 Torsional Rigidity_________________________________________ 329
14.3 Wood Strength Testing_________________________________________ 330
14.3.1 Beam Types______________________________________________ 333
14.4 Stress, Strain and Strength______________________________________ 335
14.4.1. Compression, Tension, Shear and Torsion_____________________ 340
14.5 Additional Factors Affecting Strength_____________________________ 342
14.5.1. Creep and Duration of Load________________________________ 342
14.5.2 Fatigue__________________________________________________ 342
14.5.3 Aging___________________________________________________ 343
14.5.4 Moisture Content__________________________________________ 343
14.5.5 Temperature_____________________________________________ 344
14.5.6 Growth Ring Orientation and Strength________________________ 344
14.5.7 Brashness or Brittle Heart___________________________________ 345
14.6 Deformation in Pure Bending____________________________________ 346
Sidebar-Bending Theory Glossary and Notation in This Section_______ 349
14.6.1 Beam Carrying Capacity____________________________________ 350
14.6.1.1 Beam Load Carrying Capacity Variations_________________ 351
14.6.1.2 Beam Deflection Under Load____________________________ 353
14.7 Strength Grading of Structural Timber_____________________________ 354
Sidebar. Moisture Content of Structural Timbers in Habitable Buildings.__ 356
14.7.1 Visual Strength Grading____________________________________ 357
14.7.2 Machine Strength Grading__________________________________ 357
14.8 Structures____________________________________________________ 359
Section 14 References_______________________________________________ 366
Section 15 Ecological and Environmental Issues________________________ 368
15.1 Worldwide Forest Coverage and Wood Extraction___________________ 371
15.2 Non-Wood Forest Products (NWFPs)______________________________ 376
15.3 Wood Consumption____________________________________________ 378
15.4 Tree Planting, Ownership and Management Responsibility____________ 382
15.5 Growth of Forest Protection Efforts_______________________________ 386
15.5.1 Forest Stewardship Council (FSC)____________________________ 387
15.5.2 Programme for the Endorsement of Forest Certification (PEFC)____ 391
15.5.3 Similarities and Differences Between FSC and PEFC_____________ 393
15.5.3.1 Similarities___________________________________________ 393
15.5.3.2 Differences__________________________________________ 394
15.5.5 Criticisms of FSC and PEFC_________________________________ 394
15.6 Considerate Usage of Forest Products_____________________________ 396
15.6.1 Protecting Forest Resources_________________________________ 398
Section 15 References_______________________________________________ 400
Glossary___________________________________________________________ 403
Bibliography_______________________________________________________ 428
Websites___________________________________________________________ 461
Name_________________________________________________________ 461
Subject________________________________________________________ 461
Website URL and date first accessed________________________________ 461
Appendix 1.________________________________________________________ 463
Shrinkage Factors for a Selection of Wood Species._______________________ 463
Index 465



