Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

WC Weekend Accomplishments....

Posts

WC Weekend Accomplishments....

#1

WC Weekend Accomplishments....

Dennis E Peacock

18 Nov 2013

Good Morning Everyone,

My hope and prayer is that none of you were effected by the severe weather yesterday. If you were I hope that you are ok and that all will work out for your good.

Been teaching a couple of people how to make cutting boards in my shop as well as starting work on the LOML Jr's blanket chest. My daughter is helping me with her hope chest so construction on it is moving rather slowly due to her not living here and her focus is primarily on her own marriage. Maybe I'll get some time to work through some of the finer points of the project this week.

We were in a minor accident last night while on our way to our church group meeting. A lady turned into the drivers side of our mini van and now we are about to start all the hulla-balloo with the insurance companies. She admitted fault and for us, this is not a good time for automotive accidents as holiday travel is upon us. Oh well, I'm hoping for the best.

I start oncall today...so this week is going to be "fun".

Well, that's it for me, so what did YOU do this past weekend?

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments....

#2

Re: WC Weekend Accomplishments....

Ralph Lipeles

My project was non woodworking. Last year I did an engine rebuild and cosmetic restoration on a 1979 Ford LGT 145 lawn and garden tractor. At the time I did not replace the front tires which were worn and had surface cracks. So, now I'm up to rims and tires. I removed the front wheels from the tractor. That was not as easy as it sounds. The "cotter" pins were nails, cut short and then hammered hard against the axle. The next job was to remove the tire and tube. Again, not an easy job. The tires are tubeless and breaking the beads was a nightmare. Next, clean out a ton of grease, wash the grease areas with kerosene and then wash the entire wheel with soap and water. Sand and get ready for prime and paint.

Today's job will be the same on the other front wheel. I hope that the tire removal goes easier.

Ralph Lipeles

Re: WC Weekend Accomplishments....

#3

Attended a Sculpture Workshop at UALR, Hunt Clark. *LINK*

Keith Newton

Hunt does some incredible work with a chain-saw. He is very quick and efficient at removing a lot of wood with great precision, where there is not much effort in getting through the grinding before the finish sanding starts.

His work station is a big pile of wood shavings, piled on top of a sheet of plywood out on the parking lot, with a short half log nested in the top. He starts by hollowing, fairing and some early sanding on the inside shape first. Then he saws the outside down leaving about 1/2" of wall thickness, using his foot inside to hold it down as it gets lighter.

I sure wish I could have learned what he shared with us about 20 years ago. Ben and I got there a little late, due to waiting till that morning to load the truck with wood to share with the other participants who wouldn't have a ready supply of raw wood. Their eyes got big when they found out they were welcome to lay claim to any and all of it.

I then made another run back over to my shop to get some wood from my more special stash to work with. I made the mistake of coming back with some dry really hard burled Black Tupelo. The weekend before, I had used the last sharpening on my saw chain, and stopped by the Stihl shop to buy another. The ladies behind the counter assured each other what I needed, and sold me a skip-tooth, which was not too good for this purpose, in that it caused the tip to bounce more, while using the bar end in side to side sweeping motion.

Some of the new young participants ended up finishing pieces they were, or should be proud of, while I scrapped all three of the blanks I started, which is OK, because I got more tricks than I would have expected to add to my bag-o-tricks.

If you ever get a chance to participate in a workshop by Hunt, you ought to take it. I put a link to one image below, but if you like this, you should continue to search, I failed to ask where was the best place to find more of his work.


http://www.google.com/imgres?imgurl=http://blakelyburltree.com/images/artwork/clark/Hunt_Clark_Finished/Hunt-Clark_2541.jpg&imgrefurl=http://blakelyburltree.com/artwork/artwork5.htm&h=503&w=768&sz=48&tbnid=HGbkWFBce1fSNM:&tbnh=90&tbnw=137&zoom=1&usg=

Re: WC Weekend Accomplishments....

#4

Re: WC Weekend Accomplishments....

Gary Smyth

For a long time now in my wanderings I’ve been looking to find an inexpensive dental or medical operating room light for the shop. Until last Saturday, no joy. In fact, no matter how old (or dinged) the fixture, the prices keep going up in chunks as homes get bigger and kitchen/bath designers buy directly from hospitals for their well to do clients. Even former military sources have redirected surplus to places other than depots and educational institutions.

Surprise.

While delivering stuff to Goodwill, I saw this light. It was donated the day before and the yellow color tag stated that it was a suntan light, $60. Saturday was a yellow tag day (-25%), and over age 60 ID add another ( -20%). The Ritter Castle fixture has a standard 120v plug, is 6’ tall with a weighted stand and flex arm, casters, shadow reducing reflected high intensity focused field of light. When I plugged it in, and it worked, I couldn’t say "sold" fast enough. But assembled I couldn’t fit it into car. Drove home to get tools to disassemble. When I returned under an hour later the Goodwill guy said he could have sold it twice while I was gone. What I found is a portable exam/ outpatient surgery light and originally came with a soft case. And while not the three or five multiple light circular OR light I continue to look for, I couldn’t pass it and they kept reducing the price. Kinda cool.

Re: WC Weekend Accomplishments....

#5

Ellis Walentine

Recuperation

Ellis Walentine

I had foot surgery on Friday and have been recovering slowly all weekend. I won't be walking normally for another month or two, so, in the spirit of making lemonade, I'm dividing my time between reading, monitoring WoodCentral every chance I get, and planning ahead for an exciting winter and spring. I am going to be renovating our third floor bedroom and building a very ambitious chest of drawers, among other things. The down time will let me get everything lined up in advance.

Sorry to hear about your auto accident, Dennis. Luckily, you weren't hurt.

Cheers,

Ellis