Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Spray gun question - Harbor Freight

Posts

Spray gun question - Harbor Freight

#1

Spray gun question - Harbor Freight

Joe in a Cleveland suburb

Uhg, please don't laugh at me...

I am a firm believer in you get what you pay for. I always try to buy the best I can afford, but I am considering going cheap on this.

I don't recall ever buying anything from Harbor Freight. I only remember being in the Cleveland store once 6 or 8 years ago. But while researching conventional spray guns, I ran across this:

http://www.harborfreight.com/detail-spray-gun-91011.html

I read on some spraying forum someplace that it's actually a good value and works well. I've seen this mentioned on several forums. The included 'customer reviews', for what they are worth, are good.

Why would I go so cheap? Well, I haven't convinced myself yet that going down the spraying road is right for me for several reason - the biggest is lack of room/space in my driveway due to close proximity to neighbors. Another reason is that if it doesn't work out for me, I haven't put much money into it.

If this does work out, and I think I want to get better results, I could get a better gun down the road. It seems like I wouldn't have much to lose trying this.

It's super cheap; $23.

What I intend to spray are small cabinets, desks, and so on using (most likely) water based products. Maybe stains too?

Don't bring up the expensive HVLP systems. I can't afford something like that now. Even the cheap $300 entry level systems are too much right now.

That's my rational and thinking.

So, what are your opinions? Have you used one? Just wondering what you with experience might think.

Oh, and I'm not in any hurry to buy anything. I don't think I could do any spraying now until the Spring anyway. So, maybe I'll hold off buying anything. I am still keeping an eye on eBay for a better used gun though - like the model Bill recommended.

Ok. Start laughing. I understand. :D

Re: Spray gun question - Harbor Freight

#2

Not Laughing

Mark Mandell - Gone Round In New Jersey

A siphon-feed gun will not give you good results with water-based finishes. Waterbased finishes want either a pressure feed or a gravity feed with tip size between 1.2 and 1.8, and were the driving form behind the HVLP development. If you want cheap, consider one of their HVLP conversion guns that work off your air compressor. Last time I looked they had a top-feed gun HVLP for about $16. Just make sure the needle, tip size, and air cap are the right size. You can apply stains and thin clears (shellac/lacquer) with a smaller tip set, so see if they have alternate sets to buy.

Re: Spray gun question - Harbor Freight

#3

Re: Spray gun question - Harbor Freight

Keith Newton

I'm with Mark, that is not the one you need. They have some that aren't much more moony, but with a larger tip and fan. The body is black on the larger ones.

Re: Spray gun question - Harbor Freight

#4

Re: Spray gun question - Harbor Freight

Ralph Lipeles

A friend bought the Harbor Freight touch-up gun and is pleased with the way it works.

Ralph Lipeles

Re: Spray gun question - Harbor Freight

#5

My results differ

Bill Tindall, E.Tn.

Be assured that a professional grade DeVilbiss gun sprays Target and General water borne(or how ever that's spelled) finishes just fine. note example attached


From what I have been told going the other way can be a problem. The HVLP air making systems that heat the air can cause problems with solvent based finishes. Personally, this was not a problem with the HCLP gun I had that ran off a high capacity compressor.

Re: Spray gun question - Harbor Freight

#6

Hot Air

Mark Mandell - Gone Round In New Jersey

That (+the noise) is why I don't use turbine guns. Both of my conversion guns run off my compressor and do quite nicely at 18 psi.

I actually tried my old Binks siphon-feed gun with waterborne finish. Result: Poor atomization. Yes, I might have diluted the finish, but then the build would be very slow and the opportunity for runs, drips, and other coating defects would increase.

'Sides, $24 ain't gon gitchu Pro-feshun'l lessen you hit it lucky at a g'rage sale. :D

Re: Spray gun question - Harbor Freight

#7

again, my results differ

Bill Tindall, E.Tn.

I have sprayed 3 Target products and one General product undiluted, 35 psi #30 cap and the result is a glass smooth coat. I have sprayed the desk, a small oak table, two plant stands, a kitchen bar, a coffee table and stuff I have likely forgotten with these products.

I spray everything but latex paint with my JGA gun- oil based paint( a whole house full of trim), varnish of all kinds, lacquer, conversion varnish, shellac, waterbornes, stain- oil, NGR and water based, and again stuff I have probably forgotten.

Curious what others have found.

Re: Spray gun question - Harbor Freight

#8

Re: again, my results differ

Merle

When I bought my gun from Jeff Jewitt, he recommended an Accuspray 12S and he knew that I planned to only spray WB products. I have been very happy with the ease of use and the quality of the finish I get.

Re: Spray gun question - Harbor Freight

#9

Re: Spray gun question - Harbor Freight

Merle

Joe, I can't comment on your gun selection, except as indicated in my other post that I do use a siphon gun successfully with WB products. However, unless your garage is extremely full of other tools, equipment, etc. you can make a small spray booth out of cardboard and a 20" window fan that will suffice for spraying small items. Put a furnace filter in front of the fan and it will catch most of the overspray. Change the filter frequently because the finish will clog it quickly. HTH

Re: Spray gun question - Harbor Freight

#10

Accu-12S

Mark Mandell - Gone Round In New Jersey

is a very good pressure-feed bottom-cup HLVP gun. Nice and light. Very good pattern density even at the edges of the fan. Used one at a friend's place and it did well on a portable compressor although we needed about 25psi to help make up for the reduced cfm.

Re: Spray gun question - Harbor Freight

#11

Re: Accu-12S

Mark Mandell - Gone Round In New Jersey

That gun will perform best with air flow at or above 10 CFM, but my friend's 7 cfm compressor gave pretty good results at higher pressure. More air and lower pressure translates to less overspray and better atomization.

Re: Spray gun question - Harbor Freight

#12

Re: Accu-12S

Merle

Thanks, Mark, Jeff wouldn't steer anybody wrong.

Re: Spray gun question - Harbor Freight

#13

Jeff

Mark Mandell - Gone Round In New Jersey

I bought my Walcom rig from him, and he is my exclusive source for shellacs, dyes, and finishes.

Re: Spray gun question - Harbor Freight

#14

Re: Not Laughing

Joe in a Cleveland suburb

Thanks again guys for answering my questions.

I can't go the HVLP gun route though. Need to stick with conventional gun because of the limitations of my compressor.

Thanks.

Re: Spray gun question - Harbor Freight

#15

Re: Spray gun question - Harbor Freight

Thomas S Stockton

Joe

I bought the $25 one with the black handle and it works great with solvent based finishes. A friend who does a lot of finishing recommended it and I am not disappointed. It works better than my expensive top of the line Sharpe spray gun.

For the price I would give it a try, one other thing is that the spray gun liners they sell are really convenient and make cleaning the gun very easy. Just pull the bag out and run some solvent through it.

Tom

Re: Spray gun question - Harbor Freight

#16

here is the problem

Bill Tindall, E.Tn.

If you are experienced spraying and you try something new, in short order you know if it is equivalent. Learning to spray with a gun of unknown performance could be a recipe for frustration and uncertainty. Is it me or is it the gun.

The success of the gun depends largely on the cap. This a precision device that determines the success and uniformity of atomization and delivery to the work surface. I would not presume from year to year Harbor Freight caps are made at the same factory or even if one made this week is equivalent to last week, or for that matter that the cap is optimum for spraying what ever it is that one wants to spray.

Re: Spray gun question - Harbor Freight

#17

Re: here is the problem

Joe in a Cleveland suburb

I had considered what you said.

I had the same thoughts.