Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Lubricant for tightly fitting pre-painted parts

Posts

Lubricant for tightly fitting pre-painted parts

#1

Lubricant for tightly fitting pre-painted parts

Keith Newton

I'm trying to finish a project that I started over 30 years ago. It is a porch up the street from my shop on the front of a Victorian home. Back then, the owners had found parts of some turned post, from over in Memphis. I added onto both ends of most of them, and built the deck and roof, but none of the decorative embellishments.

About a year ago, I was walking Sassafras, the pup. As I passed, the current owners were bringing in groceries. I hailed them, said that I liked their house, especially the porch. They looked at me funny, then I told them I had built it 30 years ago. They called us over to meet and talk.

Since then, they managed to buy lots of parts from another house which got torn down, then ask me to to come finish the job. I've had to make lots of new parts, and as is my nature, I cut them very close. The owners, Architect husband, and wife is president of the historic Quapaw Quarter Association. They wanted everything primed and painted before assembly, which I'm sure is a good idea.

But the question is. With the added paint and traction, what sort of lubricant can I use between the ends of the balustrade railing, to assist getting the thing together, without tearing the paint off the post, but that wont interfere with painting everything it's final coat after it is all together.

The only thing I can think of is soap, which could be washed off. Are there any other suggestions that I should consider? Painting is not my strong suit.

Re: Lubricant for tightly fitting pre-painted parts

#2

Clint Searl

Re: Lubricant for tightly fitting pre-painted part

Clint Searl

K-Y Jelly. Nyuk nyuk

Re: Lubricant for tightly fitting pre-painted parts

#3

Jesper, Denmark

Re: How about a little wet primer before assy?


Re: Lubricant for tightly fitting pre-painted parts

#4

If the paint is dry, didn't I read

Gary Smyth

here about baby powder. It is ultra fine to reduce friction, wipes/washes off with little or no trace, cheap. Medical personnel use it to ease putting on exam gloves after washing their hands (if the gloves aren't pre powdered already). Worth a test. It will also get rid of squeeks in wood floors too.

Re: Lubricant for tightly fitting pre-painted parts

#5

Re: Lubricant for tightly fitting pre-painted part

John Veerkamp

Talc

Re: Lubricant for tightly fitting pre-painted parts

#6

Clint, Real Men don't that,

Keith Newton

But then, they probably wouldn't use baby powder either, for fear of throwing off that manly aroma, but I may show up with some of all. Ha

Re: Lubricant for tightly fitting pre-painted parts

#7

Re: Lubricant for tightly fitting pre-painted part

don stephan

Create allowance as need to assemble pre painted parts, then judicious use of good caulk to fill narrow gaps. May be less expensive in long run than more difficult i.e. time consuming installation with occasional damaged part getting it into place.

Re: Lubricant for tightly fitting pre-painted parts

#8

Interesting.....

Barry Irby

When I was a kid my grandfather had some work done on his house, an old farm house. The carpenters would cut and fit a piece, then hand it to the painter who would prime it while the carpenters moved on to another piece. The backs and ends of everything got painted, or at least primed. They called it 'Back painting".

I was talking to an older builder about it some time ago and he went "Oh yeah, I had forgotten that. We used to bring all the windows and doors to the house and the painter would prime them all the way around and leave them leaning up on the trees." Everything got painted on the parts that did not show. We have forgotten all that.

The took the lead out of paint. They stopped dipping all the exterior trim in penta chlora phenol (sp?). We ran out of old growth timber. Stuff rots. Good on you for priming the stuff.

Now see if you can get it together without too much damage. Remember, caulk is makeup. Use seriously corrosion resistant fasteners.

Re: Lubricant for tightly fitting pre-painted parts

#9

Re: Silicone caulk?

Larry Clinton At Frankfort, (Central) Indiana

I have never tried it, but I would bet wiping a little silicone caulk to the surfaces would reduce the friction. Even if a little paint would be scraped off, the caulk would still "seal" the joint. This is just a guess on my part, although I do know the silicone is a good lubricant and it certainly would not have any detrimental effect. Might try it on some scrap parts and see how much it reduces the friction...

Re: Lubricant for tightly fitting pre-painted parts

#10

Re: Silicone caulk? No, that is a bad idea.

Keith Newton

That would prevent the final paint coats from adhearing.

However, a good paintable caulk might, but it would bond. I think it would be a food idea to make it easier to get apart, if ever needed to repair something, like the floor deck, which is 30 years old.

Re: Lubricant for tightly fitting pre-painted parts

#11

Re: Silicone caulk? No, that is a bad idea.

Larry Clinton At Frankfort, (Central) Indiana

I didn't expect the caulk to be applied where it would be spread onto the outer surfaces - When I glue mortice and tenon joints I don't spread the "glue" on the areas where I intend to finish. My intent was to have the caulk applied to the "inside" of the joint in a similar manner that you would with glue! Most anything that is a "lubricant" would probably have a somewhat detrimental effect on the adhesion of the final coat of paint if it is applied to the "painted" surfaces. However there are several types of silicone caulk that are sold and advertized as "paint-able". I can't say how well they work.

Re: Lubricant for tightly fitting pre-painted parts

#12

Ellis Walentine

What I'd do

Ellis Walentine

I'd find a very thin sheet of some kind of tough UHMW plastic or delrin and hold it against the post while angling the baluster into position. Once there, just pull out the delrin.

Ellis

Re: Lubricant for tightly fitting pre-painted parts

#13

sounds like a plan

Bill Tindall, E.Tn.

I didn't understand the details of the problem(and maybe still don't) till Ellis provided a solution. If indeed the problem is wedging the rails between posts and not fitting the vertical things (that I can't spell) into their holes then the Ellis solution seems perfect. If you can't get the plastic sheet out, just trim it back to where it doesn't show. A milk jug or 2L soda bottle or bubble wrap from some some recent purchase should be about the right thickness and strength to attempt withdrawal. The soda bottle or bubble wrap will be strongest and less likely to tear.

Re: Lubricant for tightly fitting pre-painted parts

#14

Wax On, Wax Off

Mark Mandell - Gone Round In New Jersey

Sounds like some paste wax would do well for the install, then wipe it off with mineral spirits and Bob's-Yer-Uncle [no idea where that Aussie bit came from, but love it].

I do the same thing to protect the area around M&T Joints from glue squeeze-out stains.