Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Some advantages of spraying

Posts

Some advantages of spraying

#1

Some advantages of spraying

Bill Tindall, E.Tn.


1. Speed It took about 4 minutes to mix finish and clean up and less than a minute to spray the whole chest.

2. Smoothness It was about 60 degrees and low humidity so the finish flowed perfectly. The coat was glass smooth. (first coat always has some rough bits from dust, and what ever. First coat will be lightly sanded and a second coat applied in an hour or so.) The finish was dust free in a few seconds, hard enough to sand in an hour and could be recoated in an hour.

3. Taylor finish to need For this piece I am spraying Sherwin Williams conversion varnish. It is durable and resistant to solvents. I could have refinished with shellac like what was on there originally, or varnish, lacquer, waterborne, milk paint, alkyd paint, etc.

Re: Some advantages of spraying

#2

Re: Some advantages of spraying

Yonak

Bill, I have a couple of question about spray finishing :

My experience is it's a pretty fine line to find the correct body of the material (how much to thin it), versus the volume and pressure of the spray so it doesn't leave an orange-peel finish or tend to sag, which leads to :

Do you spray large flat surfaces vertical, flat, or on an angle and, if horizontal or at a low incline, turning the gun vertical really doesn't work, so how do you do it ?

Re: Some advantages of spraying

#3

Bill, I seem to remember you writing

Gary Smyth

that you use a traditional (not HVLP) gun. Did I remember correctly? What are you using? Is it a full cup gun? What is the capacity of your compressor? I tried using my two horse, two gallon mini EmGlo portable but my results are less than what I want. I'm experimenting so it could any combination of the gun, the compressor, the mix, and/or me. I never use it all day just relatively quick jobs, I read the directions but any shortcuts to limit errors?

Re: Some advantages of spraying

#4

Re: Some advantages of spraying

Bill Tindall

my internet is "wounded" this AM so answer brief....more later when better...

My experience is it's a pretty fine line to find the correct body of the material (how much to thin it), versus the volume and pressure of the spray so it doesn't leave an orange-peel finish or tend to sag........ if finish flows from the cup at 35 psi I declare success and spray. The only finish I need to thin much is alkyd paint and varnish. If too much finish is coming out I reduce the flow needle valve.If too little or none, thin some.If it dries too fast add thinner. I use a professional DeVilbiss gun JGA 502, 30 or 42 cap and 3M PPS cup.

Learn to spray water on a vertical test surface.

Do you spray large flat surfaces vertical, flat..........when convenient..... or on an angle......no....... and, if horizontal or at a low incline.....when necessary. turning the gun vertical really doesn't work....it does with my gun. But, with the 3M pps system I can spray upside down. handy on some things

Re: Some advantages of spraying

#5

Re: Bill, I seem to remember you writing

Bill Tindall

that you use a traditional (not HVLP) gun.........see above

I tried using my two horse, two gallon mini EmGlo portable but my results are less than what I want....... you need to be able to keep up with air needs of your gun at 35 psi.

learn to spray water on a vertical surface. No finish job will be harder to control than thin water.

approach spraying to minimize overspray on surfaces already finished.

Re: Some advantages of spraying

#6

Re: Bill, I seem to remember you writing

Joseph Mulherin, sr

Bill is entirely correct in his method of spraying his furniture. I did 9 cars one year doing almost exactly that way. The best was an Alfa Romeo, it had a battery in the right rear fender which got hit and exploded leaking acid all over. I repaired the fender with fiberglass, smoothed it all out and sanded smooth; then sprayed the cat an International Orange. When the car was sitting at the curb the paint looked like it wanted to flow off the fender and sides....perfect paint job...INMHO

Re: Some advantages of spraying

#7

Re: Some advantages of spraying

Joe in a Cleveland suburb

So, to get into spraying finish, you don't need to spend $600+ on a HVLP system?

I've been trying to do a little research by looking at older FWW articles. Seems like I read conventional spray guns don't spray water based finishes well. As I recall the article said the conventional spray guns can't atomize the finish properly - I may recall that wrong or misunderstood, and/or the water based finishes are better now than when that article was written. I really don't know - just learning what some of this stuff means.

I can pick up a cheap spray gun off eBay, hook it up to my crappy compressor and have at it?

It seems there is a dizzying array of products out there for spray finishing from guns to compressors to the type of product you are going to spray. The options seem endless.

Where do you start? It seems like you have to have a PhD in Chemical Science with a secondary degree in Mechanical engineering... I'm confused. :b

Re: Some advantages of spraying

#8

Re: Some advantages of spraying

Bill Tindall

it may be important to use a quality gun. DeVilbiss and Binks are reliable brands. DeVilbiss JGA guns were popular in cabinet shops. The cap needs to be suitable. A number 30 is about right for furniture,but I can get a number 43 to do fine also. Any compressor that doesn't spew oil is fine. you need a few cfm at 35 psi.

A mentor for an hour will be of great value. Worth paying someone at a cabinet shop for an hour of training. Practice spraying water on a piece of paper.

Lacquer is formulated to spray easy, but anything that can be made thin enough will work. Shellac is the hardest. Suppliers to auto body shops are a source of advice as well as suppliers of lacquer.

Stop by any time for a lesson. I had my daughter spraying in 15 min.

Re: Some advantages of spraying

#9

Re: Some advantages of spraying

Larry Clinton At Frankfort, (Central) Indiana

Bill I agree with everything you have stated. I would certainly also say that many if not almost all the issues people have with spraying are 1) they try to spray too thick a finish - I spray shellac, lacquer and thinned Minwax poly (and other varnishes) with very little problem - but I often spray 3 or 4 (or more) quick drying thin coats instead or 1 or 2 "thick" coats. And 2) they worry to much about getting a solid coat on during each spray. I don't worry much if I "miss" a spot or an area seems light - after a quick, light sanding with steel wool, or 400 (or high) sandpaper or very fine abrasive pad to rub out - then wipe (I've taken to using the "microfiber" cloths for my Tack rags) and respray, the light areas are well covered the next layer. When spraying poly I change my solvent mix to make sure the coating levels and still dries fast. I use acetone or Naptha when the temp is low - mineral spirits when hot or if the humidity is high - often a mix of the solvents.

I have a couple of good Bink's guns and also a few HF HVLP conversion guns. The only time I use the conversion guns is when I am spraying inside deep shelves or things like a box. There is less bounce back and I can see better what I am doing!

Re: Some advantages of spraying

#10

What do you mean

Joe in a Cleveland suburb

"I have a couple of good Bink's guns and also a few HF HVLP conversion guns."

When you say 'conversion' gun, what does that mean?

Thanks.

Re: Some advantages of spraying

#11

Re: Some advantages of spraying

Merle

Joe, an excellent reference is Spray Finishing Made Simple by Jeff Jewitt. It includes a DVD so it is easier to understand than just reading about spraying. I also agree with the others that learning to spray with water and paper or cardboard is a great way to get started. HTH

http://www.amazon.com/Spray-Finishing-Made-Simple-ebook/dp/B007NLCDMM/ref=sr_1_1?s=books&ie=UTF8&qid=1383069249&sr=1-1&keywords=spray+finishing

Re: Some advantages of spraying

#12

agree with Jeff Jewitt


Re: Some advantages of spraying

#13

Re: What do you mean

Bill Tindall

they convert high pressure high volume air from a large compressor to HVLP air at the gun. handy for someone with a large compressor like for air driven sanders. most won't have a compressor big enough to run one

Re: Some advantages of spraying

#14

Re: Some advantages of spraying

Joe in a Cleveland suburb

Thanks.

I just ordered this from Amazon.

I thought about getting it directly from Jeff as his shop is just a few miles from me. But Amazon's price was a little better.... :)

Thank you.

Re: Some advantages of spraying

#15

Re: What do you mean

Larry Clinton At Frankfort, (Central) Indiana

Bill answered correctly. Link to similar gun here http://www.harborfreight.com/20-oz-high-volume-low-pressure-gravity-feed-spray-gun-69705.html

I have a fairly large 60 gal stationary, rated 7 HP (actually around 2 true HP) compressor with a good filter system so these work ok for me. Can't say I would use these type guns for a table or similar item as I don't think the spray is as even or as well dispersed - but does work better for deep cavities, like the inside of a chest or deep shelves. As I have said before I like to spray several thin coats vs 2 or 3 thick ones. So I use a smaller tip, I also probably run my gun pressure a little higher than I should so I get more "bounce back".

The amount of finish I waste on my projects does not concern me, yeah the cost is somewhat higher, but my concern is the quality of the finish.

Relativity I use quite small amounts of finish material. So the few dollars I waste is not a concern. If I were making large quantities of cabinets or furniture for profit, I would probably change some of my methods.