Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

OT Cutting aluminum?

Posts

OT Cutting aluminum?

#1

OT Cutting aluminum?

Jim in N. Va

I need to make a baffle for a heater out of sheet aluminum. I was thinking of cutting up some cookie sheets for the aluminum parts, but am not sure of the best way to cut. Too heavy for shears. Any advice for cutting the parts with either my band saw or table saw? Or other suggestions?

Re: OT Cutting aluminum?

#2

lots of options

Bill Tindall, E.Tn.

band saw works if you have a fine tooth. 6 tpi might work but finer would be better. 4 tpi is scary (now how do you suppose I know that?) . Saber saw works well too and you can get fine toothed saber saw teeth. You can use a table saw if you can find a very fine toothed blade. I have a 7" blade steel blade that I use. It makes a LOT of noise. But, be wary of the aluminum sticking to the teeth. I have had that happen on thicker stock. Not good. Band saw is safer.

Re: OT Cutting aluminum?

#3

Re: lots of options

Barry Irby

Bill is right. I have cut it with a bandsaw, Tablesaw saber saw, hack saw, snips etc. The fine tooth blade(s) is important.

Also, wear eye protection. Seriously, wear eye protection. Maybe ear protection too.

I also found out the filings stick to the rubber wheels on the bandsaw. Clean them after you finish.

Re: OT Cutting aluminum?

#4

Re: OT Cutting aluminum?

Keith Newton

For straight cuts, I like the TS, with a sled, with low hook triple chip blade, and scrap of MDF under to make zero clearance on both sides of the blade.

As stated, full face shield, and welding gloves.

Re: OT Cutting aluminum?

#5

Re: OT Cutting aluminum?

R Payne

I'd use a shear (but I happen to have a small beverly). Lacking that a good cold chisel (with a bit of practice it works nearly as well as a shear). An angle grinder will work but the cutting disk will likely be ruined. I don't like cutting aluminum with woodworking tools though it can be done.

Re: OT Cutting aluminum?

#6

Ellis Walentine

Metal muncher

Ellis Walentine

I used to use a nibbling tool I called a metal muncher that essentially snips a 1/8" kerf in sheet metal.

Ellis

Re: OT Cutting aluminum?

#7

Re: lots of options

William Duffield

You can use a table saw, but NOT a SawStop. DAMHIKT!

Re: OT Cutting aluminum?

#8

A couple of ideas *LINK*

Tom Dunlap

Either of these will work.

I've got a Kett sheep's foot shear and use the dickens out of it.

The same mechanism mounts on your drill too.

either way you'd be ahead of the game if you had some extra jaw screws. They're socket head cap screws and not easy to scrounge or source at the time they break...Sunday evening ;)

http://www.coastaltool.com/a/ab/kett/kd-200.htm


Drill powered cutter

Re: OT Cutting aluminum?

#9

DAMHIKT! ??????

Keith Newton

Oh, William,,,,,,,,,,,,,,,,,, Say it ain't so! You didn't really, did you? ha

Tell me that you watched someone else do that. Otherwise, I'm afraid I'm going to have to ask you to lean in real close to your computer so I / we can deliver your dope-slap. Although I can imagine that if someone slides a piece of aluminum up to the blade, the slamming of the brake is probably a pretty instantaneous slap.

Re: OT Cutting aluminum?

#11

Re: DAMHIKT! ??????

William Duffield, on the Cohansey

It was a much more subtle mistake than you are imagining. My wife had some bound documentation that she needed to unbind to run through a copy machine. It appeared to be all paper, cloth and glue, but inside the cloth binding was a very thin layer of metalized mylar. I cut several of the bindings off with no problem, cutting through the top and bottom invisible layers of aluminum with no problem. But then I moved the fence a smidgen, and the blade ran through the about 1/2" vertical layer of the back of the binding, and BAM! I immediately knew what had happened, as I've sacrificed several hot dogs to Mr. Gass's mechanism in demonstrations, but it took some careful examinations to figure out why it happened. No headslap is necessary when you trigger that brake. "The air was shattered by the force of Casey's blow."

The brake and the Freud Fusion blade make a great shop clock.

Re: OT Cutting aluminum?

#12

Re: Bad Dog Biter, maybe?

William Duffield, on the Cohansey

I've seen this nibbler demonstrated at woodworking shows, but haven't used one.

https://baddogtools.com/styled-6/styled-7/index.html#