Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Rifle case - long

Posts

Rifle case - long

#1

Rifle case - long

Don in Central Illinois

One of the young women in my church has asked me to build a rifle case for her boyfriend. Since, I'm usually on the turning forum and don't do a lot of flat work, I need some help. From the example she showed me, it is going to be a simple box, big enough to hold a rifle with a mounted scope. Don't know if I should use nice plywood or dimension lumber,like hard maple or walnut. Also, 3/4" stock or thinner? Don't want it so too heavy, without the rifle. Any idea of some plans i could find online? Any help appreciated. It is for a Christmas present, so I have a little time. As always, thanks in advance for any help ya'll can give.

Re: Rifle case - long

#2

Re: Rifle case - long

Brian from Monument

Is the case intended to be display or a working case?

Re: Rifle case - long

#3

Re: Rifle case - long

Don in Central Illinois

Working. Similar to what Cabellas have, but made from wood. She wants something ' made to order' not like everyone else has.

Re: Rifle case - long

#4

JL

Re: Rifle case - long

JL

IMO, I'd use the thinnest stock you could get away with. Ideally 3/8" or 1/2 plywood. You want it to be light weight enough to pick up and move.

Is this for transport in a vehicle or plane? If it is for a plane - I wouldn't even attempt the job.

Rifle cases take some abuse - have box corners. They get opened up a lot - so you may want to glue a hardwood edge on the plywood. Storage for accessories is always nice - e.g. some sort of compartments in the body of the case.

Re: Rifle case - long

#5

Re: Rifle case - long

Philip Duffy

I have made several gun cases. The best ones have 1/4 ply bottom with brass/steel corners for protection against dropping or breakage. I use thin hardwood stock on the top, ie, 1/4 and the sides. The compartments are laid out inside to hold cleaning gear, a cloth for wipe-down, etc. and the dividers are all very thin -- 1/8in and glued in place. A rifle can weigh 8 or 9 lbs and a case needs to be strong to protect it so don't spare the glue and joint reinforcements. Also, I use piano hinges and strong lock assemblies. So far, my cases have survived, even airline checking. Philip

Re: Rifle case - long

#6

Re: Rifle case - long

John in NM

Thinner stock is better as a rule, you want to keep the case light.

If an attractive exterior is a must, I would use 1/2" or 5/8" stock for the sides, and a 1/4" baltic birch panel with matching veneer for the top/bottom. My own preference would be to make a sturdy BB plywood box and cover the whole thing with leather - but that's a whole 'nother can of worms, and may not be the look they want anyway.

For the inside, the easiest approach is English fit dividers (there was a post maybe 6-8 months ago by David Barnett about these). Its basically straight dividers wrapped in fabric that roughly outline the item that lives in the box. You can also do French fit, which usually entails a closer cutout with some padding under the fabric.

Traditionally, felted wool fabric is used for the inside of these cases, it can be a very refined look (that's probably why I would go with leather and felt - that's the traditional way).

Re: Rifle case - long

#7

Re: Rifle case - long

Don in Central Illinois

Thanks all. I think 1/2" plywood with walnut edging. Piano hinge ( had already decided on that ) and heavy duty locks. If she decides to have me make it, and I remember, I'll post some photos.

Re: Rifle case - long

#8

Re: Rifle case - long

William Duffield

For hardware for protecting the corners, Chris Schwarz has recently been doing a lot of research for an upcoming book on campaign furniture and has reported on quality and availability of hardware on his blog at Lost Art Press.

http://blog.lostartpress.com/category/books-in-the-works/campaign-furniture/

I definitely would not rely only on brass and glue and screws for the structural integrity of the box. Dovetail the corners and inset the top and bottom in grooves (not just rabbets). Where the top meets the case, you should consider a half lap joint to provide additional integrity and some protection against dust intrusion. If you have access to the rifle during construction, you should consider French fitting (or English fitting, as John recommends) the case to the particular gun. It will prevent the bun bouncing around in the case and putting the scope out of alignment.

I hope he's planning to use this weapon to shoot deer. If he has wolves or "Commies" in his sights, I would decline the commmission. :D