Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Titebond molding

Posts

Titebond molding

#1

Titebond molding

Bruce, a MN Galoot

I glued up some laminations to make a rocker the other night. I placed the clamped up form on top of the extension table (formica covered particle board) on my table saw. When I came back two days later, this is what I found:


I definitely don't want to see this happen when there is no way to plane or saw off the offending material. Fortunately, when I ripped the rocker more or less down to working size, the joints didn't seem to be affected.

I've never, ever seen it mold in 30 years of using Titebond. What's up with that? Is there any explanation for this?

Re: Titebond molding

#2

JL

Re: Titebond molding

JL

You left it wet. It molded. It happens. That's why I usually leave extra on the sides.

When I steam bend, I usually leave it 1/8-1/4" thick - and I shave it down. After a week in the drying box, it can get stained and moldy.

Re: Titebond molding

#3

Re: Titebond molding

Bruce, a MN Galoot

I suppose that's a possibility, but the humidity right now is very low. I've done laminated glue-ups like this dozens of times (and usually during humid MN summers), and this is the first mold that bothered to show up.

Re: Titebond molding

#4

Bob

Re: Titebond molding

Bob

Wow that open up a lot of questions. Did you steam it first? How old is the glue? Is it really Mold? I know that when glue comes in contact with metal it has a reaction with it, could this be something like that? Maybe the wood? That's a puzzle.

Re: Titebond molding

#5

Re: Titebond molding

William Duffield, on the Cohansey

It looks like mold from here, but…

The photo is a bit low resolution, and the wood species is not obvious. so there might be a couple other possibilities. Did you set it on the cast iron table saw top before moving it to the extension table? Or, had you been doing some sharpening on the extension table before the lamination? If so, it could be a tannin/iron reaction. If so, you can deactivate it with a bit of oxalic acid, e.g. Bar Keeper's Friend. If you're sure it's mold, next time you might try putting some battens between the lamination and the table top, to allow the glue on the surface to dry a bit faster. I'm thinking something like plastic chop sticks, or pick-up-sticks, or coffee stirrers.

When I get mold, it's usually because it's been exceptionally hot and humid lately, or the wood has been left in proximity to the concrete floor.

Re: Titebond molding

#6

Re: Titebond molding

Bruce, a MN Galoot

It's oak, not steamed before bending (only a 3" bend over 30")

The table top is Formica, and the air is dry as a bone. The wood had been on top of my bench for about two weeks prior to cutting and gluing.

I should have used some sort of spacer if only to keep the mess off the extension table.

Re: Titebond molding

#7

Re: Titebond molding

Bill Tindall, E.Tn.

are you sure it is mold and not iron stain

Re: Titebond molding

#8

Jack Guzman from Maine

Re: Titebond molding

Jack Guzman from Maine

Bruce, assuming that it is indeed mold and not iron stain ,my guess is that the mold was already present on the wood and the moisture from the glue and leaving it to dry gave it time to bloom.Never seen that myself either.---Jack

Re: Titebond molding

#9

Re: Titebond molding

Bruce, a MN Galoot

That's about what I'm thinking too, Jack.

Re: Titebond molding

#10

Re: Titebond molding

Bruce, a MN Galoot

I'd thought about that, Bill, but both the workbench and extension table were clean.

Re: Titebond molding

#11

Re: Titebond molding

pecker

I had a gallon of Titebond glue once that had greenish black mold growing right in the jug. The manufacturer replaced it and said it occasionally happens.

So there's a remote possibility it started in the glue.