Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Table Saw dead??

Posts

Table Saw dead??

#1

Table Saw dead??

chrispy

I am in the process of making a fancy planter. Ply carcss clad in masarandaba ( beautiful, but hard, heavy, and expensive, eats up blades, silica??). This morning my Sears table saw just hums with no rotation. What's up?? (Sears wants $320.60!!! ludicrous!!)

SEARS Saw

Part # 113.298720

89031P0547 (SERIAL # ?????)

MOTOR

MFG Model# C55CYA-1859

(I believe it to be 1HP, 3450 RPM)

Any advice please

Re: Table Saw dead??

#2

Not dead, just ill

Lee Schierer in McKean, PA

It sounds like your start capacitor has died and doesn't kick the motor over to start. Replacement should be about $20-30. Go to the Sears web site with your saw model number and you should be able to order one.

You may also be able to get one from any motor repair shop in your area.

It will be located in a bump on the side of the motor. Just be sure to disconnect the power before working on the motor.

Lee

Re: Table Saw dead??

#3

Re: Not dead, just ill

JMOHNIKE

Mine did the same thing. I removed the belt, turned on the motor and tapped the shaft. The motor did start to turn and picked up speed. I kept blowing out the motor with an air hose while it was running. alot of sawdust. I decided to remove the motor take it apart clean it and lube it. Put it back on the saw and have had no problems. this was 2-2 1/2 yrs ago, and my saw gets used 7 days a week. Good luck.

Re: Table Saw dead??

#4

Re: Not dead, just ill

Yonak

Before ordering parts, chrispy, it couldn't hurt to inspect the saw to be sure there's not something wedged somewhere stopping the blade, belt or motor from turning. The blade isn't tilted against the insert, is it ? I've done that before.

Re: Table Saw dead??

#5

Re: Not dead, just ill

chrispy

Thankyou all for your replies. The blade turns freely so I do not think that anything is jamming it. I will replace the starter cap as it is cheap, but do not think that it is that as it seems to hold it's charge. I've blown a lot of dust from the motor and will try the "tap" test afer replacing the cap. I'll keep you posted. The saw died 2 hours before the wood was delivered, C'est La Vie!!!

Re: Table Saw dead??

#6

Re: Not dead, just ill

Lee Schierer in McKean, PA

You can pull start a motor with a bad capacitor by wrapping a string around the shaft so that when you pull it off the motor is turning in the correct direction, then hit the power switch. If the motor comes up to speed, it is a bad cap.

Lee

Re: Table Saw dead??

#7

Re: Not dead, just ill

wayne goldstein

It could be the starter switch. Try blowing it out with the motor running if you can get it started by winding a string around the shaft to spin it, but be sure to pull the string by holding with two fingers. This prevents the string from wrapping around the shaft and pulling your hand into the shaft.

Re: Table Saw dead??

#8

Re: Not dead, just ill

Bruce, a MN Galoot

Agree that it could be dust on the starter contacts. I had this problem for quite a while until I decided to take it apart and fix it properly. Turned out to be worn out contacts on the centrifugal switch. The motor repair guy had spares. and charged me $5.

Re: Table Saw dead??

#9

Re: Not dead, just ill

Ralph Lipeles

The starter cap just helps a motor start under load. Remove the belt from the pulley to see if it then starts. If it starts, the cap needs replacing. If it still does not start. I would look elsewhere, starting with opening up the motor and cleaning the centrifugal starting contacts.

Ralph Lipeles

Re: Table Saw dead??

#10

Re: Not dead, just ill

Bill Howatt

I wouldn't say this is a definitive test. If the capacitor goes open it has the same electrical effect as the switch being stuck open. I've also seen motors that will not start even with no load without a properly operating starting circuit - which is why the references to spinning with a string to get it going.

Bill

Re: Table Saw dead??

#11

It's probably pining for the fjords.


Re: Table Saw dead??

#12

Re: Table Saw dead??

chrispy

> Thankyou Lee. I have tried (Carefully using a stick) to rotate the

> motor with power on to no avail, I have ordered the start capacitor,

> and have been researching both McMaster Carr and Grainger for similar

> motors, all > $300 I' afraid!

> Chrispy

Re: Table Saw dead??

#13

Re: Table Saw dead??

John McGaw

If it really is a standard sort of 1HP motor as you suggested originally you should be able to find a replacement for < $200. Grizzly sells some for ~ $175. Ebay is worth a look. Much depends on the frame style and mounting and speed etc but they are out there. Of course rebuilding, if needed, can be a lot less expensive than that.

Re: Table Saw dead??

#14

Re: Table Saw dead??

chrispy

Searched craigslist, ebay, etc and found several complete saws like mine for about$150, including a 3hp version. Cannot go to look until Monday, will keep you advised, wish me luck. An upgrade to 3hp from 1hp would be nice, but would require transfer of my Beismeyer/Exacta rails and fence, (Here we go!!)

Chrispy

Re: Table Saw dead??

#15

Joe Bradshaw

Re: Table Saw dead??

Joe Bradshaw

Chrispy, where are you located? I have a Craftsman TS that is just sitting in my barn. You are welcome to the motor, just pay the shipping.

Joe

Re: Table Saw dead??

#16

Re: Table Saw dead??

Chuck

Yep if you don;t want to remove the end, clean the Centrifugal switch , reassemble said motor, just pony up the cash and buy another one! Remember sawdust is the switches enemy.

Re: Table Saw dead??

#17

Re: Table Saw dead??

chrispy

Thanks for the offer, I'm in Atlanta GA, 7760-998-7219, please give me a call

Chrispy