Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Floor Finish Question for Jason Roehl

Posts

Floor Finish Question for Jason Roehl

#1

Floor Finish Question for Jason Roehl

David McDonnel "Mac"

Jason or others,

I have pulled up the carpets in my sister's '40s era house and the floors look real good, nice patina with minimal dark spotting. They need some cleaning and a new layer of finish. What's my best approach to save the current look? I have refinished (sanded) several floors but have not tackled cleaning and top coating. Special products? Procedures? Recommendations? Thanks in advance!

Mac

Re: Floor Finish Question for Jason Roehl

#2

Re: Floor Finish Question for Jason Roehl

Bill Tindall, E.Tn.

I have done two old floors. I scuff sanded the finish to remove top oxidized layer, wax, dirt, etc. then top coated with urethane varnish.

Re: Floor Finish Question for Jason Roehl

#3

Re: Floor Finish Question for Jason Roehl

jim Hoeller

I recently installed about 1,250 sf of oak flooring and used a new Minwax product: Oil modified, water based polyurethane in a satin finish. The coverage was excellent and used about 3.5 gallons to apply 3 coats. After 10 months the floor looks good. Application of the second and third coats required very good lighting to avoid missing any areas. The cost was $50.00 per gallon but the coverage, relative ease of application and almost no odor made it a bargain.

Re: Floor Finish Question for Jason Roehl

#4

how to pick a finish

Bill Tindall, E.Tn.

If the intention is for the finish to protect the floor then here is a simple test to weed out the weaklings. Many stores have samples of the finish on some wood or another. See if you can dent the finish with your finger nail. The gold standard of floor finish, moisture cured urethane , can not be dented and it will last decades. Others range from coming close to soft.

Re: Floor Finish Question for Jason Roehl

#5

Jason Roehl in Lafayette, IN

Re: Floor Finish Question for Jason Roehl

Jason Roehl in Lafayette, IN

You pretty much can't go wrong with Bona products. That said, I consider the Mega to be a minimum--there is a lesser line sold at some of the box stores, but I can't recall the name of it offhand. To preserve what you have, do what you have to do to clean it--sweep, damp mop (mild detergents at most, nothing that leaves a residue), then rent a floor buffer (hit a tool rental place--they'll have what you need more than likely) and screen it with 150 or 180 grit screens, whatever the finish you use recommends for re-coating.

You should get about 250 s.f. out of each side of the screen, then you can use one of the used screens or some sandpaper of the same grit to get the tighter areas by hand. A buffer with dust collection hooked to a shop vac would be best, but even with that, you'll have to carefully vacuum the floor, then go over it with a damp terry cloth towel to get the dust.

To put down the finish, there's nothing like using one of these:

http://floormechanics.com/duratool_floor_coater_lightweight_12-7712.php

with one of these:

http://floormechanics.com/duratool_12_applicator_sleeve-8014.php

Pour the finish in a line near the edge of the room and "snowplow" the finish back and forth parallel to the grain as you work your way across the room. I'm sure there's a YouTube video or a thousand. If you're feeling Tim Taylor-ish, the applicators come in 18" and 24" as well (I think I saw a 30" at one point, too...).

Jason

Re: Floor Finish Question for Jason Roehl

#6

Re: Floor Finish Question for Jason Roehl

David McDonnel "Mac"

Thanks Jason! I'm not likely to get to it soon enough. Is there someone you know down here in Indy that would be interested in a two room and one hallway job?

Re: Floor Finish Question for Jason Roehl

#7

Jason Roehl in Lafayette, IN

Re: Floor Finish Question for Jason Roehl

Jason Roehl in Lafayette, IN

Sorry, Mac, I can't say I have any real connections in the Indy area. Best I can suggest would be to hit up friends, family, church members and the like to see if any of them have had similar work done and could recommend someone.

Jason