Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

When do you sand?

Posts

When do you sand?

#1

JL

When do you sand?

JL

I always sand after assembly as a matter of course - clean up the glue marks (if any). I always sand shaped areas before assembly (afterwards also) - to make sure the shape is what I want it to be.

Usually my planer and my jointer leave a fairly good surface - my knives are in pretty good shape.

I was thinking on it though and wondering - how many people sand before doing the joinery work (cutting dadoes, dovetails, etc.)? How many people sand before assembly?

Re: When do you sand?

#2

When The Cuttin's Done

Mark Mandell - Gone Round In New Jersey

the sanding begins. Sanding, in my shop, is part of the final fit to the joinery. Everything is then dry-fit. Other than reducing a finish film, the only instances that I can think of where I sand after glue-up is to flush-up proud finger joints or dove tails or adjust a drawer slide/guide.

Re: When do you sand?

#3

PS

Mark Mandell - Gone Round In New Jersey

And surfacing cutting boards, of course ;)

Re: When do you sand?

#4

Bob

Re: When do you sand?

Bob

http://youtu.be/NLtoLtmquco Here is the way I like to finish my projects

Re: When do you sand?

#5

ditto

Bill Tindall, E.Tn.

Tops of course are sanded after glue up and edge profiling. In fact I treat tops as a separate piece of "furniture". They get made and finished independent of the rest. The last construction step of something that has a top is top installation, then it's ready to be put into service.

Re: When do you sand?

#6

Before assembly

John in NM

I pretty much do as Mark and Bill do, though I sometimes put a coat of oil on just before assembly - makes any glue removal trivial.

To some degree, it depends a lot on what you are building. A table with the rails flush to the legs would be about as easy either way. The same table with the rails set in from the legs is a pain to sand after assembling.

Re: When do you sand?

#7

Both!

Tony - Memphis

Depending on the piece/part, I'll do some sanding before, during, and after. I'm building a desk right now with molding that overhangs the sides by 1/8". I'll sand those sides before assembly and then clean them up a bit just before finishing. This is especially helpful when you have a cross grain situation and need to avoid scratches. Also, this same piece has a frame surrounded by edging. I'll clean up the assembly before routing the profile so I won't damage the finished edge. By clean up, I mean sand it through to 220 - removing glue, leveling joints, etc.

I like the idea of a coat of oil or other finish before assembly to make glue removal easier. That could help in some situations too. I've read that some folks use wax and then clean the wax off before finishing. Never tried that.

Tony

Re: When do you sand?

#8

Bob

Re: Both!

Bob

Tony I posted a video on the way I do it. Basically I use a card scraper then 320. I found this to cut down on sand paper cost drastically as well as cut the time in half not to say the least about dust. 320 may seem a bit high but I have never has an adhesion problem in the 5 years of doing it this way.

Re: When do you sand?

#9

Depends

Mark Mandell - Gone Round In New Jersey

On the wood you're using. Domestic hardwoods rarely benefit from abrasive grits above 180 or 220; Higher grits are mostly for sanding finish films including wet-sanding oil finishes where the slurry is used as a grain filler. If you go to the exotics and tropicals, it's a different story.

Re: When do you sand?

#10

Dealing with glue where it shouldn't be

Bill Tindall, E.Tn.

I am surprised that woodworkers that have demonstrated considerable skill in building fine furniture are dealing with glue squeezing out where it shouldn't (by oiling and the like)rather than avoiding the problem to begin with. This isn't a problem an experienced woodworker should have. Inexperienced woodworkers should be learning how to avoid it as they develop their other skills.

I took a class in the Mack Headley and Sons shop (a woodworking life altering experience, should you ever get the opportunity to take a class there). Steve and Jeff emphasized proper fitting joints and proper glue application on these joints. If glue is squeezing out where it shouldn't too much was applied, end of story. From their lectures I got the impression that their students typically used too much glue it was their mission in life to fix this problem.

It takes but two molecular layers of glue molecules to create the bond, one stuck to one side of the joint and vice versa. Any additional glue either fills the gaps or gets (or should get) squeezed out.

Unless it is a joint where excessive squeeze out doesn't matter I rarely apply glue from the glue bottle. I have a collection of small cups I get at the restaurant supply store (used for salad dressing etc) which I add glue to. It gets transferred from here to the joint with an acid brush (the metal handled affairs with the short stiff bristles which I buy by the 100) or a thin small lab spatula. The spatula is ideal for M&T joints where glue can be slathered in the mortise but only a very thin layer goes on the tenon. The spatula both applies and scrapes off the excess. Larger glue surfaces are coated using the acid brush. Very large surfaces are coated with a paint brush. But in all cases glue is applied as though it was paint and I wanted to avoid runs.


Years of practice avoiding squeeze-out becomes essential when dealing with an application like this cock beading. Here is a place the acid brush was used, painting on a thin coat of glue on both surfaces up near but not up to the show edge.

Bottom line-strive to avoid squeeze out rather than deal with it later.

This seems to sound too preachy but I'm too tired to try to fix it. The objective is to provide encouragement, not criticism.

Re: When do you sand?

#11

Re: Dealing with glue where it shouldn't be *LINK*

Jesse Cloud

Bill,

I agree with your views on squeeze out. I had a couple of teachers who always said "Better too much glue than not enough" and encouraged squeeze out as long as it didn't get on the clamps or the floor. Boy am I glad those days are gone!

Another glue applicator to consider is an irrigation syringe. Got this idea from Steve Latta's stringing video. It can apply the tiniest bit of glue in just the right place. Its cheap and if you wash it after use it lasts forever.

By the way, if you're pals with a vet or a dentist, you could probably talk them out of one for free...


Irrigation syringe on Amazon