Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Charging for shrinkage

Posts

Charging for shrinkage

#1

Charging for shrinkage

Yonak

If you buy dried, rough sawn lumber from a lumber yard do they add in a percentage for shrinkage ? In other words, if you bought lumber that measures out to be 500 bf, will they tack on a percentage to the board foot total, say 550 bf, to calculate what you will pay ?

Re: Charging for shrinkage

#2

Re: Charging for shrinkage

Dave Bair

I buy my wood from a century-old lumber company. They never charge for shrinkage. However, if the lumber is milled to less than an inch, you are charged the original 4/4 price.

Re: Charging for shrinkage

#3

No

Mark Mandell - Gone Round In New Jersey

If I buy a 1x12 [rough] I am charged for 1bf for each lineal regardless of it's actual dimension. I don't buy a 7/8x12 for 7/8bf/lineal and then get 15% tack on for "shrink" from the original wet-milled 1" dimension. If, however, I were to buy S2S, there would be an up-charge for the planer.

Re: Charging for shrinkage

#4

Re: Charging for shrinkage

Sgian Dubh

Possibly. It might be a good idea to check what kind of ‘tally’ the yard uses to sell its stock. There are two types of tally: the green or wet tally, and the dry or nett tally. Inadvertently buying wood on the green tally means you’ll drive out of the yard with about 10% less wood than you expected.

Green or Wet Tally is the volume of the wet wood prior to drying. Dry or Nett tally is the volume of wood after it’s dried. Between wet and dry there is a reduction in volume as the wood shrinks due to moisture loss. The loss varies from species to species but it’s usually between about 7% and 9%. Slainte.

Re: Charging for shrinkage

#5

Here is the complete story

Bill Tindall, E.Tn.

We bought and sold hardwood lumber for 30+ years so I have some perspective on this topic.

Historically, hardwood lumber was traded at the wholesale level with the tally based on the lumber being measured , and sometimes graded, before kiln drying. Experienced buyers and sellers knew the convention and there was no problem with this convention so long as it was understood by all that it was the accepted convention.

However, retail buyers get their shorts in a knot over this convention if and when they encounter it. Volume buyers and sellers knew the system and there was no misunderstanding or controversy. Every pack of KD lumber we ever bought for resale had 7% added to the tally.

Some years ago someone, or group, sued the National Hardwood Lumber Association (they set the measuring and grading rules for hardwood lumber in the US) over this practice. Confusion ensued, for now some wholesalers added the 7% and some didn't. To add to the confusion the details of how the 7% got added, or not, varied.

To navigate this situation a knowledgeable buyer needed to ask about the basis of the tally and reputable sellers divulged the basis for the tally to the buyer, either wholesale or retail.

On a personal note, to avoid the confusion we bought on a "shrunk" basis because that was the practice of our suppliers, added this

shrink" to our cost and sold on dry measurement. Our customers never had to worry about this convention. A critical point- We didn't have any competition pricing on a predried measurement so we were at no disadvantage for taking the route we did.

The bottom line of it is if you are buying from a business that caters to volume customers it is wise to ask on what basis the lumber was tallied and graded and accept the answer without knoted shorts. Obviously the economically significant customers for this business are satisfied with what ever practice they use. Don't expect them to change what they do to accommodate a 50 bd ft customer.

Again , on a personal basis, our typical customer was a cabinet shop or other woodworking business that bought hundred or more bdft quantities on each order. We would sell to individuals so long as they were willing to accept our business practices geared to our volume customers. If not they could shop at Woodcraft where the 2X higher price was enough to accommodate their expectations.

Re: Charging for shrinkage

#6

Re: Here is the complete story

Mark Nowicki

I have a veneer supplier in Montreal who, on occasion, sells some nice wood (quantity decided by him, strapped on a pallet, take it or leave it ).

He refuses to put any signage on his place of business, fearing that it will attract customers that want the benefit of retail service at wholesale prices.

Mark

Re: Charging for shrinkage

#7

Re: Here is the complete story

Bill Tindall, E.Tn.

Been there and done exactly that.

Re: Charging for shrinkage

#8

Re: Here is the complete story

Dave Bair

Sorry, but charging for shrinkage sounds like a convoluted method to reduce the apparent cost by charging less per board foot and making up the profit by adding a surcharge. Why not just charge 7% more per board foot to begin with?

Re: Charging for shrinkage

#9

Re: Here is the complete story

William Duffield

Because they figure it out when the run the log through the saw. The shrinkage is different depending on the species, and even on how long it has dried. You are paying the sawyer for his value added. It's the fair way to do it.