Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Thank you to Bill Tindall, Saw blade....

Posts

Thank you to Bill Tindall, Saw blade....

#1

Thank you to Bill Tindall, Saw blade....

Barry Irby

Bill has been promoting the use of "skilsaw" blades on table saws for years on Wood Central. Generally 7 1/4" blades. I was cutting a sheet of plastic laminate. 5' by 12' and was still squeezing it for all it was worth. I happened to have a 6 1/2" blade handy and tried it. Much narrower kerf than my ten inch blades. Worked great. Left it on the saw for cots in between the cutting of the Formica. Effortless ripping.

Thanks Bill, I will be looking at better quality 7 1/4" blades even thought the little framing blade I had did fine.

Re: Thank you to Bill Tindall, Saw blade....

#2

craigd

+1

craigd

After that discussion and Bill and David Barnett's comments/recommendations, I went to Home Depot, got a $16 Freud 7 1/4" blade and have been very happy. The 10" blades rarely see the arbor anymore.

Re: Thank you to Bill Tindall, Saw blade....

#3

One thing to remember...

John in NM

Framing blades often have a very aggressive hook angle, 20 degrees or so. Most of the time an aggressive blade on a table saw won't present a problem, but I would be a little extra careful using one.

Similarly, I once used a friend's RAS that had a 7 1/4" framer blade on it. Utterly terrifying! :D

Re: Thank you to Bill Tindall, Saw blade....

#4

Re: Another Limitation

William Duffield

Another limitation is that they don't work on a SawStop, because the brake cartridges can't sense the saw teeth more than about 1/8" away from the brake shoe. Other than that, Steve Latta also recommends them for making stringing and inlay banding, because they waste a lot less wood, which is important when it's something expensive like holly or ebony, or a block of intricately patterned banding that you've spent a lot of time and effort and expensive materials building up.

If you happen to have a SawStop and want to do Federal Period work, but don't want to buy your banding, there is an alternative, but it's going to take you quite a bit of inlay to recoup the cost. A company called Total Saw Solutions makes a Microkerf 40 very thin kerf 10" table saw blade that cuts a kerf that's even thinner than the Freud blades. It's an excellent blade, but needs to be treated with care (no cutting of PTSYP 4x4 posts), and it's $185.

http://www.totalsawsolutions.com

Another trick Steve Latta does with these cheap ATB Freud blades is to use them to cut dovetails. If you break off every other tooth, you can tilt your saw blade at about 10° and cut the sloped side of the dovetail with a flat bottom. Which teeth you break of depends on whether you have a left tilt or a right tilt table saw.

Re: Thank you to Bill Tindall, Saw blade....

#5

Jack Guzman from Maine

Re: Thank you to Bill Tindall, Saw blade....

Jack Guzman from Maine

I missed something. Where was this recommendation of skilsaw blades made? I don't believe I ever read that thread. Anyone have a link to any of this?---Jack

Re: Thank you to Bill Tindall, Saw blade....

#6

summary of the 7 1/2" blade story

Bill Tindall, E.Tn.

For several years I have used a 7 1/2" or 8" thin kerf blade on my 10" table saw. Some are much better than others at producing a finish cut. The "industrial" quality blades from CMT are good, for example the 40T ATB blade, the equivalent blade from Stehle #20-1579, or the Freud blade, all 40T ATB and costing about $25. One of these blades just stays on the saw except for very special cutting. Most who have tried them stay with them.

I have never recommended "skill saw " blades. They are good for dirty lumber and plywood but they are not the blade I keep on the saw.

Advantages:

1. They don't produce kick back and this is the primary reason I use them. As a demo I have started a rip in a short piece of lumber then let it go. It either sits there or slowly retreats from the blade.

2. They do not throw cut off ends.

3. They cut effortlessly so again they promote safer cutting. There just isn't much force on the lumber.

4. They are cheaper than 10" blades and they can be resharpened.

5. They make less dust and are more quiet.

Re: Thank you to Bill Tindall, Saw blade....

#7

Re: Thank you to Bill Tindall, Saw blade....

Barry Irby

I have done Bill something of a disservice. I don't think Bill Actually said a "Skilsaw" Blade. He did talk about similar blades and perhaps 8" very thin kerf blades.

I don't have a SawStop and did not think of that limitation. For those of you fortunate enough to have one, follow the manufacturer's directions and don't void the warranty and do't lose the protection.

I bought a Extremely low end Porter Cable set of tools at Lowe's on close out for $99. A drill, Reciprocating saw, drill, Circular saw, two batteries and a charger. The batteries were toast, but Porter Cable replaced them with the extra sized ones. (Lucky Me) the little 6 1/2" saw came without a blade and I bought a two pack. I used the second one on my TS (10" Rockwell Contractor Saw) and have been amazed at how well it works.

Re: Thank you to Bill Tindall, Saw blade....

#8

Bill Jumped in while I was typing, Thanks


Re: Thank you to Bill Tindall, Saw blade....

#9

Jack Guzman from Maine

Re: summary of the 7 1/2" blade story

Jack Guzman from Maine

I never thought of trying a smaller blade in my tablesaw.I'm going to give it a shot. Thanks ---Jack

Re: Thank you to Bill Tindall, Saw blade....

#10

Jack Guzman from Maine

"Skilsaw"

Jack Guzman from Maine

I have always used the term"skilsaw" as a generic word word meaning any handheld circular saw that uses a 7 1/4" blade.So,when I read Barry's post I assumed he was talking about a 7 1/4" blade in general. It is just what most people mean when they use that term.---Jack

Re: Thank you to Bill Tindall, Saw blade....

#11

Re: summary of the 7 1/2" blade story

Keith Newton

Bill, I was in on one of those earlier discussions and recommended doing this. I've been using them as my main blade for around 15 years.

Besides the advantages Bill mentioned, obviously thinning the cut takes less power, but the torque is also higher as the diameter gets smaller. The combination of thinner and smaller diameter, can give the same effect as doubling the HP of the motor. So if any of you that still have not tested this, next time you are making heavy cuts in some tough material, which is loading the motor, smoking the blade, just think of it as down-shifting.

Re: Thank you to Bill Tindall, Saw blade....

#12

Exactly what I meant...

Barry Irby

Now that I think about it I suppose the generic term is "portable circular saw". (I saw one the other day that used a 16 3/4" blade. I would be terrified to try it.)

I too have always used the term skilsaw for them. Hard habit to break. But Jack is right, I meant the smaller blade.

Come to think of it, that's another thing they stole, except that it was a Black & Decker Sawcat left over from the days that brand was better than it is today. I earned a living with that saw when I was a younger man and I am going to miss it.

East coast is direct drive and west coast is worm drive, Right?

Re: Thank you to Bill Tindall, Saw blade....

#13

Re: More SawStop blade info

William Duffield

You can safely use an 8" blade on the SawStop, with the dado brake. You cannot use a 6" dado stack or one of those 7-1/4" blades (e.g., Freud Diablo). There is no way the saw will even start. You cannot use the key to override the brake in those cases.

Now, for the scary part. This I DO NOT recommend, but it can work. A friend modified a SawStop brake by attaching (screwing, bolting or riveting?) a precisely machined aluminum block to the brake shoe to bring the surface of the built-up shoe close enough to one of those Freud 7-1/4" blades that the computer would sense it. He made it work, but I'm sure he voided the warranty on the brake in the process. I also don't think he did the hotdog test on it to make sure it actually stops the blade quickly enough and doesn't come apart in the process. I decided it made more sense for me to buy the MicroKerf 40.

Re: Thank you to Bill Tindall, Saw blade....

#14

Jack Guzman from Maine

Beam saw

Jack Guzman from Maine

I operated one of those big bladed saws. They're used in timber framing to cut big beams. They are pretty heavy but as soon as you pull the trigger you get a surprise. Centrifugal force makes the saw feel pretty light in your hands. It is a strange feeling.---Jack

Re: Thank you to Bill Tindall, Saw blade....

#15

Re: summary of the 7 1/2" blade story

R Payne

If you think it won't kick back, I really think you're kidding yourself.

What you describe, letting a partially cut bit of wood sit there, I've seen done with 10" blades, that alone won't convince me a smaller blade won't produce kick back.

Re: Thank you to Bill Tindall, Saw blade....

#16

Barry---   I still have my supper saw cat saw

del schisler

i still have mine i use all the time, it work's very well , I got it when it first came out, i remember when you were looking for a part for your's, i guess part's are not to be had, oh well i guess all good thing's come to a end.

Re: Thank you to Bill Tindall, Saw blade....

#17

Re: Parts for Sawcat

William Duffield

http://www.ereplacementparts.com/black-and-decker-2694-71434-industrial-strength-sawcat-parts-c-4167_4252_9494.html