Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

OT: Bathroom Addition - Low Water Pressure

Posts

OT: Bathroom Addition - Low Water Pressure

#1

OT: Bathroom Addition - Low Water Pressure

Paul Leuba

My wife and I are planning an addition of a bedroom with bathroom by extending the first floor of our house to eliminate running the stairs as we age. We are now above 70 and planning to stay in our house indefinitely. So, the first floor addition is a safety issue as well as a convenience issue.

We are on a well with the pressures set at 35 - 55 lbs. The new bath will be about a 12 feet rise above and about 92 feet linear run from the well tank with approximately 6 - 90 degree ells in the pipe run. Needless to say, I am concerned over the expected pressure drop between the expansion tank and our proposed new bathroom.

What options do we have to ensure that the water pressure in the new bath is adequate?

Paul in Hunt Valley, MD

Re: OT: Bathroom Addition - Low Water Pressure

#2

Re: OT: Bathroom Addition - Low Water Pressure

Bill Tindall, E.Tn.

At one time my water meter was 1700 feet from the house with a 1" line in between. Pressure drop across this line, plus the house plumbing was insignificant at typical water flows. If you run 3/4" pipe your pipe pressure drop will be insignificant. The drop from pushing the water uphill is about 15 psi per 30' elevation gain.

If you endure one of the government regulated water delivery devices (shower head etc) and haven't ripped the restrictor out the flow will be so piddly that pressure drop is nothing to worry about.

Re: OT: Bathroom Addition - Low Water Pressure

#3

Re: OT: Bathroom Addition - Low Water Pressure

Keith Newton

Each doubling of diameter, quadruples the area within the pipe, which can be fine for the cold side, but will take 4 times as long to get the hot from the tank to the outlet, so don't over-size the hot line if you are very far from the heater.

Re: OT: Bathroom Addition - Low Water Pressure

#4

Re: OT: Bathroom Addition - Low Water Pressure

Paul Cates - Henderson, KY

Don't worry about it. My well is 175' from the house and peak pressure at the pump is in the upper thirties. Sixteen 90 degree ells surrounding the sediment filter in the garage plus all the other ones. Granted, the flow at an inside faucet is not the best, but it's mostly because of the scale buildup inside the 35 y.o. copper pipe.

Re: OT: Bathroom Addition - Low Water Pressure

#5

Re: OT: Bathroom Addition - Low Water Pressure

john Veerkamp

Worst case scenario, if the pressure drop is too great there are in line booster pumps that can be installed later if necessary.

Re: OT: Bathroom Addition - Low Water Pressure

#6

Re: OT: Bathroom Addition - Low Water Pressure

Paul Leuba

Thanks for the timely and good feedback.

I will have a 3/4" cold water feed run to the bathroom and hope for the best. A small hot water heater is being installed adjacent to the bathroom to eliminate the long draw time and cooling associated with a long hot water pipe run. In the event that the pressure is too low, we'll add an inline booster pump later.

Paul in Hunt Valley, MD

Re: OT: Bathroom Addition - Low Water Pressure

#7

Re: OT: Bathroom Addition - Low Water Pressure

Pete in Holland, MI

35-55 psi operating range ?

How big is your accumulator tank? Does your pump cycle short bursts, or long periods between cycles ?

If your tank is adequately sized, and pump doesn't cycle all that often, raise cut-in pressure to 40 or 45 psi.

What others are talking about in pipe diameter are resulting in flow concerns. Larger pipes WILL give you greater flow in the system. Pressure, going up a story or two, IS a concern. It takes approimately 1/2 PSI per foot to lift water, regardless of pipe size. Thus, adding 12' of lift to the water from where you measure 45 psi, should yield 39psi at the discharge point.

Pure physics.

Pete

Re: OT: Bathroom Addition - Low Water Pressure

#8

Re: OT:Obvious answer

Larry Clinton At Frankfort, (Central) Indiana

You will lose approximately 1/2 lb of pressure for each 1 foot of rise. However I have installed and setup many pumps - Your current pump setting of 35 cut-in 55 PSI shutoff is pretty factory standard. However most pumps and tanks are rated for far higher pressure (the pump will run longer if it is set higher to achieve the higher pressure) and can be set to 40-45 cut-in and 60-75 cutout pressure - many will operate fine at up to 100 PSI. Normally nothing is required except to remove the cover from the pressure switch and adjust the low (cut in) and range screws to achieve the pressure you want. Might look at your pump owner manual to see what range your pump is capable of operating. You may not find it necessary but is an option.