Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Swollen Chair Leg Tenons

Posts

Swollen Chair Leg Tenons

#1

Swollen Chair Leg Tenons

Paul Leuba

I carved the seat and turned the legs and stretchers for 3 Windsor sack back chairs in February and March, and then had to sit the project aside after cutting the leg tenons and drilling the leg holes in the seats. It is now the end of July and I've returned to the shop after dealing with a family health issue to discover that the tenons have swollen with the summer heat and humidity here in central Maryland. They no longer fit the holes I drilled and I believe it is unwise to reduce them in size because they will certainly shrink when the Winter low humidity arrives, and leave me with loose chair legs.

I have considered building a small light bulb powered kiln to reduce the moisture in the tenons and hopefully shrink them back to where they comfortably fit into the previously drilled and fitted seat holes. However, I am not sure that this will work as intended, and I have no information on the size, wattage or configuration of a workshop constructed kiln that would be appropriate for this purpose.

I would appreciate any feedback the forum could give me on the matter.

Re: Swollen Chair Leg Tenons

#2

Hot sand

Bill Tindall, E.Tn.

Curtis Buchanan has a UTube series on chair building and in it he will describe how he dries green leg tenons. When he has demoed for the club I recall he used hot sand.

Re: Swollen Chair Leg Tenons

#3

Re: Swollen Chair Leg Tenons *LINK*

Bruce, a MN Galoot

Bill's idea will work very well, as low tech as you can get.

For a bit more involved, but still low tech solution, take a look at the kiln that Curtis Buchanan uses. His kiln is at the very beginning of this video:


Curtis Buchanan's splendid Chairmaking series

Re: Swollen Chair Leg Tenons

#4

JL

Re: Swollen Chair Leg Tenons

JL

The light box kiln will work. I usually wrap everything in foil except the tenon and put it in a hot box.

The hot sand will work also, I've done that once in a while. All in all, I prefer a gentle heating.

Re: Swollen Chair Leg Tenons

#5

Jack Guzman from Maine

Re: Swollen Chair Leg Tenons

Jack Guzman from Maine

Paul,

I built a kiln using 250watt bulbs in three ceramic light holders. I use a thermostatic switch(Chicken breeding supplies) to regulate the heat and a computer fan to move the air. However all you need to do for this situation is fill a pan with sand and set it on a hot plate. Once it is hot set the tenons in the sand and heat them until the tenons shrink back to size. Don't leave them in there long enough to turn them brown.---Jack

Re: Swollen Chair Leg Tenons

#6

Re: Swollen Chair Leg Tenons

Don Stephan

My inclination would be to dry the tenons only enough to fit the mortises, checking the fit foccasionally as the wood gets warmer. If the tenons are too dry they may suck the moisture out of the glue too quickly for a strong glue joint. For the same reason, I'd let the tenons cool to room temp before gluing. Just my two cents.

Re: Swollen Chair Leg Tenons

#7

Re: Swollen Chair Leg Tenons

Pete in Holland, MI

Running your AC, and the house is dry? Move them inside for several days.

Re: Swollen Chair Leg Tenons

#8

Re: Swollen Chair Leg Tenons

Paul Leuba

Thank you, everyone for the input. I will try a simple light bulb kiln with a thermometer to monitor the heat, keeping it warm, but not to hot. I will test the fit frequently so I do not over do it.

Paul in Hunt Valley, MD

Re: Swollen Chair Leg Tenons

#9

Jack Guzman from Maine

air movement

Jack Guzman from Maine

Don't make your container air tight. Air movement across the object is important to drying. I put a hole in a bottom corner and another in the opposite top corner and use a tiny fan to pull the air at the top hole. It works without the fan,just slower.---Jack