Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Semi-OT: Sealing Concrete Floor?

Posts

Semi-OT: Sealing Concrete Floor?

#1

Semi-OT: Sealing Concrete Floor?

David Hay Denver

We're in the final inspection stage of a new workshop and I'm starting to think about what, if anything, to do with the concrete floor before I move all my tools in. Right now, I don't think I want to deal with the time and expense of doing an epoxy floor. After all, it's only a shop, not a showroom floor. By the time I install cabinets, tools, benches, and rubber mats, there's not going to be much left of the floor to see.

Mainly I'm looking for something that's reasonably easy to clean up should I happen to spill a stain or some other kind of finish. And I don't want to have to re-apply it every so many years.

So I'm currently thinking about using some kind of penetrating sealer... something analogous to a grout sealer. Are there any brands or products that are recommended? I've run across products from Quickrete and Seal-Krete at the big box stores. Sherwin Williams carrys H&C Products. But I'm not sure if these are just a surface coating or something else.

Or should I stop worrying about the floor, power wash it and just move my tools in?

Thanks!

David

Re: Semi-OT: Sealing Concrete Floor?

#2

JL

Re: Semi-OT: Sealing Concrete Floor?

JL

By all means - seal, paint or do something to the floor.

It makes a real difference with dust. Bare floors seem to generate dust. It is much easier to sweep a painted or sealed floor. Make it a different color - it is much easier to find part (screws, nuts, bolts, dowels, etc.) on a floor that is something other than concrete gray.

I would recommend against a latex. My preferences are for a reasonable two-part paint - such as an epoxy because it is solvent resistant. A solvent resistant paint is easier to clean and can be cleaned using solvents. Which means when you get grease, dirt or whatever - hopefully you'll be able to get it up. You can usually pop glue up from many two part paints.

Re: Semi-OT: Sealing Concrete Floor?

#3

Re: Semi-OT: Sealing Concrete Floor?

Mark Mandell - Gone Round In New Jersey

Lots of penetrating top dressings around. One thing to note is that some of them have a bunch of silicone in the formulation as a waterproofer which makes them a no-no for a wood shop. You need to check the formulas.

Re: Semi-OT: Sealing Concrete Floor?

#4

paint it a light color

Bill Tindall, E.TN.

Painting it a light color will significantly improve the light situation. With a gray floor any light that passes the bench is absorbed never to be seen again. A light floor will reflect significant light back to where it may be useful (according to brother in law the lighting engineer)...wish I had done it.

Otherwise, seal so it will be easier to sweep.

Re: Semi-OT: Sealing Concrete Floor?

#5

Re: Semi-OT: Sealing Concrete Floor?

John Veerkamp

By All means seal it I used a clear concrete sealer on my garage/shop and a latex paint on my basement/studio floor. The paint I used is a porch and deck paint and has held up well for 9 years. Some wear and staining under and around my lathe but I'm pleased overall with the durability. Keeps down dust and makes sweeping up a breeze.

Re: Semi-OT: Sealing Concrete Floor?

#6

Re: Semi-OT: Sealing Concrete Floor?

Dave Bair

The quart of Minwax poly I spilled on the shop floor has lasted forever, filled the concrete's pores and imparted an attractive amber tone to the affected area. I probably wouldn't apply it so thickly if I'd actually done it on purpose, though.

Re: Semi-OT: Sealing Concrete Floor?

#7

Jason Roehl in Lafayette, IN

Murphy's Law of Finishes.

Jason Roehl in Lafayette, IN

They will only permanently bond and look fresh indefinitely where and when you don't want them to.

Jason