Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Woodcraft Grinder Toolrest

Posts

Woodcraft Grinder Toolrest

#1

Woodcraft Grinder Toolrest

Barry

I have a Woodcraft slow-speed grinder that I use mostly for sharpening turning tools. I use a Wolverine jig, so I don't use the grinder toolrest very much. I tried to sharpen some bench chisels this week and found that the grinder toolrest is not perpendicular to the grinding wheel or the bracket that supports it. I was actually grinding the chisels at an angle like a skew, not straight across. I spent some time trying to true up the rest with a file, but was not very successful. It's better, but not by much. Has anyone else had this problem? Is it worth the effort trying to fix it, or should I just buy an after-market toolrest like the Veritas or maybe build my own wooden rest?

Re: Woodcraft Grinder Toolrest

#2

Re: Woodcraft Grinder Toolrest

Bob Entwisle in NJ

Doesn't the platform for the wolverine system pretty much work as a tool rest for grinding chisels and such? Or is it too high, and/or wide to get the chisel into the wheel?

Bob in NJ

Re: Woodcraft Grinder Toolrest

#3

Re: Woodcraft Grinder Toolrest

Barry

Oh, it would work just fine, except that my Stanley bench chisels are old and somewhat short. Too short to reach the grinding wheel, anyway. It may be time for new chisels, but the old Stanleys really do have a lot of metal left. I have seen a new narrow tool rest for the Wolverine system somewhere. My local Woodcraft doesn't have it. I may have to try to order it. That would probably solve my problem. Thanks

Re: Woodcraft Grinder Toolrest

#4

Re: Woodcraft Grinder Toolrest

William Duffield

I have a Veritas rest as wel, and don't use it for the same reasons David has enumerated.

If your chisels are short, make a jig for your Wolverine, from hardwood or BB ply or acrylic or whatever. Three pieces. The base rides on top of the tool rest, a narrow fence attaches to the back of the bottom to track the back edge of the tool rest, a platform on top of the base, towards the front, with clearance behind for the short tool handle. You'll probably want to bevel the front edge of the base and platform to bring the front edge of the jig closer to the wheel.

Re: Woodcraft Grinder Toolrest

#5

Re: Woodcraft Grinder Toolrest

Dick Coers

You can use the long V rest from the Wolverine for chisels. You can even sharpen chisels that are wider than the wheel. I just takes a deft hand to keep a straight grind. I've sharpened up to 1 1/2" chisels this way, on a 1" wheel. The honing stone makes it dead straight. I use the Veritas holder, in conjunction with the Wolverine platform rest for plane blades. Tilt the Wolverine platform rest up at a steeper angle, you just want to use the top edge. Rest the protruding tongue on the back of the rest, against the top edge of the Wolverine. Slide it back and forth to grind the blade. I'll take a pic if you want, it's hard to describe. I like this method because the Veritas holder is not trapped. It is just a pivot action into the wheel, then tilt back to clear it and inspect the grind.

Re: Woodcraft Grinder Toolrest

#6

Re: Woodcraft Grinder Toolrest

William Duffield

That's a good idea configration-wise, but you still have the problem David identifies in his post: You are rubbing aluminum against steel with an abrasive in the mix. If you could intercede between the soft and hard metals with a piece of hard wood, you would have less problems with smoothly sliding the Veritas holder back and forth.

Re: Woodcraft Grinder Toolrest

#7

Re: Woodcraft Grinder Toolrest

Jason Waters

I have the Veritas. I've had it for a long time, and didn't pay the $69 they want for it now. If I were doing it over and at today's pricing, I would build one like the other poster mentioned based on Ian Kirby's article.

I do ok with the Veritas, but it doesn't do all that I need to do. I don't seem to have the grit issue that's talked about, but I only sharpen a few tools at a time.

Jason

Re: Woodcraft Grinder Toolrest

#8

Re: Woodcraft Grinder Toolrest

Dick Coers

Never had any issues sliding it back and forth. The stone is 1" wide, plane blade maybe 2 or 2+". Not a lot of sliding unless I am restoring a clunker plane. It's almost impossible for the abrasive to get under the holder while grinding.I've done this for probably 15 years? Can't remember when all that stuff came out, but my Wolverine bases are made of steel.

Re: Woodcraft Grinder Toolrest

#9

Re: Woodcraft Grinder Toolrest

William Duffield

Yes, the Wolverine is steel. It's the Veritas Grinding Jig that is aluminum, and therefore subject to galling and substantially increased sliding friction when abrasive grit gets between it and the Wolverine. Of course, it's easy enough to prevent with an air hose, or to fix with a fine file.

http://www.leevalley.com/US/Wood/page.aspx?p=32974&cat=1,43072,45938

For anyone who doesn't grasp your recommendations, at the link are illustrations of some of the configurations that work with the Wolverine, thus avoiding the need for the kind of wobbly Veritas tool rest.

Re: Woodcraft Grinder Toolrest

#10

Re: Woodcraft Grinder Toolrest

Dick Coers

I was referring to the Wolverine base being steel on my old unit. They use an aluminum extrusion now, but were originally fabricated from steel. Thanks for posting the link.

Re: Woodcraft Grinder Toolrest

#11

Re: Woodcraft Grinder Toolrest

William Duffield

Sorry, I misunderstood. Yes, getting abrasive between the parts of the Wolverine is also a serious problem, and when it stops working smoothly, I have to go get my pneumatic hose and a dust mask before I can continue sharpening.