Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Band Saw Blade For Resaw

Posts

Band Saw Blade For Resaw

#1

Band Saw Blade For Resaw

Tom Rex in TX

In your humble opinion what is the best brand of resaw bandsaw blades?

Where are they sold?

TIA,

T Rex

Re: Band Saw Blade For Resaw

#2

Jim in Burlington Ont.

Re: Band Saw Blade For Resaw

Jim in River Oaks, Ont.

I use a 3 TPI 3/4" Timberwolf, have used one for years as my Go To resaw blade...

Take care,

Jim

Re: Band Saw Blade For Resaw

#3

Re: Band Saw Blade For Resaw

Bruce, a MN Galoot

I have two, a 1/2" Wood Slicer from Highland Hardware that cuts really well, and a 1/2" Lenox Tri-Master, carbide tipped and very expensive. However, it can be resharpened. The Wood Slicer has a thinner kerf and takes a bit less power, which is nice.

Re: Band Saw Blade For Resaw

#4

JL

Re: Band Saw Blade For Resaw

JL

Timberwolf by Suffolk Machinery

Woodslicer by Highland Woodworking

I've tried both, I like both. I wouldn't get more than a 1/2" blade.

Re: Band Saw Blade For Resaw

#5

http://www.supercutbandsaw.com/


Re: Band Saw Blade For Resaw

#6

Re: Band Saw Blade For Resaw

GolfSteve in Calgary

In my humble opinion, the Laguna Resaw King is the best I've used. I bought one as a prequel to my guitar project and am amazed at how smooth it cuts. With that blade I've repeatedly achieved tolerances that are quite astounding - eg. cutting a bunch of strips exactly 67/1000" thick (1.7 mm), then resetting the saw, cutting a bunch of strips 52/1000" thick (1.32 mm). The cuts are so smooth that I pass some 400 grit sandpaper paper over the cut edge a few times, taking the strips down to their final thicknesses of 65 and 50/1000"

However, for general furniture making work, including sawing your own veneers (say 1/8" thick), I would not spend the money on the $250 carbide tipped Resaw King. Just buy good quality $30 blades, adjust the tracking properly, and replace them often.

ps. I also have some bent-up carbide Lennox Tri-Master blades that came with my used 18" bandsaw. The Tri-Master blades are much thicker (stiffer) than the Resaw King - so thick that I can believe they would fail more quickly due to bending fatigue, as you read about on the Internet, than the Resaw King. However, the Lennox blades were much less expensive and are really sharp.

Re: Band Saw Blade For Resaw

#7

Bob

Re: Band Saw Blade For Resaw

Bob

Laguna Re-saw King is what I use. I have the same one for 6 years its 2TPI X 1" I cut 1/16" veneers no sanding required. I sent it back to be sharpened 2 years ago and they even replaced a few teeth. Not cheep but you get what you pay for so why not just spend the money one time and have the best.

Re: Band Saw Blade For Resaw

#8

Re: Band Saw Blade For Resaw

jcousins

laguna resaw king. laguna has great customer service for their blades - fixed a broken weld, sharpen. my only xperience has been with their bs blades.

use it for resawing veneers xclusively

jerry

Re: Band Saw Blade For Resaw

#9

Bob

Re: Band Saw Blade For Resaw

Bob

Ironic, I had just cut a spalted sycamore log 6" using my Laguna King blade and must have hit something! I need to send it back to be sharpened, I think I will ger a new one as well. I got about number of 3/4" X 18" from 2 logs