Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Thinning Titebond

Posts

Thinning Titebond

#1

Thinning Titebond

David C. Lykins

Hello everyone, first let me say that I sure miss my shop more than you can imagine, but hopefully some day I'll get to set up my tools again and make some sawdust.

Anyway, I've had several occasions where I wondered if I could make Titebond, I usually purchase Titebond II, thinner. For some reason I was thinking that I read a post or other article indicating that you could actually just use water?

Any information is GREATLY appreciated.

THANKS!

Re: Thinning Titebond

#2

Why?

Bill Tindall, E.TN

A more reliable answer could be had if you described the need. But, in general this kind of adhesive can be thinned 5% ONCE with water to slow down tack. Excessive thinning will affect bond strength.

These adhesives consist of a suspension of mushy balls of polymer in water, called a "latex". They work by the water diffusing away into the wood. The mushy balls of polymer coalease into a tough plastic film which holds the joint together. Same process as latex paint drying except in this case the polymer balls are made mushy with solvent which evaporates and leaves the room smelling like "fresh paint".

Re: Thinning Titebond

#3

Re: Thinning Titebond

John McGaw

I've thinned Titebond with water to the consistency of paint for

use as sizing but I'm not sure that I'd trust it as an actual adhesive after thinning.

Re: Thinning Titebond

#4

Why Not?

Neal in San Jose

Waaaay back in my wayward youth, I flew model airplanes. Control line combat to be specific, and those planes usually had short, exciting lives. It was my SOP to use Titebond (there was only one at the time) thinned approx 30%, mostly to reduce weight and improve glue flow into joints. In inspecting MANY crashed airplanes, I don't think I ever saw a glue-line failure. The wood always failed. But, and it is a biggee, the wood was balsa.

I've used thinned white and yellow glue on other wood, like when trying to get it into a hairline crack. It works, but I generally don't bother any more.

Re: Thinning Titebond

#5

Re: Thinning Titebond

Jesse Cloud

Franklin told me that TB I could be thinned up to 10%. Many of us here in the Southwestern arid desert will pour out the glue we will need for the glueup and carefully add a bit of water. It modestly extends the open time. Some of the projects I have made this way are ten years old now and no sign of problems.

Re: Thinning Titebond

#6

Re: Thinning Titebond

William Duffield

I've successfully thinned it 10% with deionized water and applied it with a roller to veneer and substrate, and then reactivated it with an iron to attach the veneer to the substrate after it has dried. In this application, it helps to have a spray bottle of water to wet the other side of the veneer to minimize curling. Also note that the reactivation time is limited, and shorter with TB II and much shorter with TB III.

Hammered hot hide glue works a lot better for this application.

Re: Thinning Titebond

#7

Re: Why - Yep, Balsa wood

David C. Lykins

Funny that you should post this, its EXACTLY why I was thinking of thinning it, not so much for building but someone (not me believe it or not) got over zealous sanding the sheeting on the leading edge of the wing to paper thin. So I was thinking of brushing on some thinned Titebond to re-glue and strengthen that area.

However I can't remember the other reason that I was thinking of thinning Titebond, but it was for something I was gluing up that was "hardwood".

Re: Thinning Titebond

#8

alternative

Bill Tindall, E.TN.

You might consider cyanoacrylate for this task. It penetrates where as the yellow glue will not. With the cyanoacrylate you will turn the balsa where it absorbs into tough plastic. If you are going to thin the yellow glue and apply it like paint you might as well use paint, lacquer, etc.

Re: Thinning Titebond

#9

Re: alternative

William Duffield

CA will work in the short run, but over a few years, it gets more and more brittle. If it is just an aerodynamic surface you are fixing, it might work fine, but for a structural repair on an airframe, subject to dynamic loads and vibration, it may not be the best solution.

I suppose it depends on how long before you expect to fly it in. :D Solvency of wood glue in methanol, nitromethane and castor oil may also be an issue, but I can't offer any advise there, because the glues I use now are not the same as the glue I used before Testors airplane cement was found to get you higher than the airplane itself.

Re: Thinning Titebond

#10

Glusize

Mark Mandell - Gone Round In New Jersey

When doing lacquered pieces with MDF components, I thinned TB-I 50/50 for a size and sealer to prepare the surface for topcoating and to strengthen edges and corners. Worked quite well, much cheaper and faster than using epoxy, and the items have stood up for a number of years' of use.

That said, I would be wary of thinning the product by a significant amount were I using it for structural bonds since you would be reducing the amount of solids needed to make the joint.

Re: Thinning Titebond

#11

Re: alternative

David C. Lykins

Hi Bill, I was trying to find an alternative for cyanoacrylate (CA) glue as the balsa has already been sanded fairly thin and though CA would soak right into the balsa, its REALLY difficult to sand flush on soft wood.

However I do use CA most of the time.

Re: Thinning Titebond

#12

Video shows how *LINK*

Jesse Cloud

This is a little off track, since I think the discussion in the thread was about structural strength, but I just viewed an interested video in which Ernie Conover thins Titebond to use on veneer. Even more interesting, the video was sponsored by Titebond.


Titebond/Ernie Conover video

Re: Thinning Titebond

#13

Re: Video shows how

Dave in Bryn Mawr

Ernie says this is good for small areas. I've used it for areas as large as a 14 x 30 table top with good results. However, I learned that thinning and three coats are best, which I appreciate. The only problem I have is when my wife says "Where's my iron!

Re: Thinning Titebond

#14

Re: Video shows how

Don Stephan

Couldn't play the video but the text suggests its showing how to let white or yellow glue dry and then reactivate it with a hot iron to glue veneer? I did this once on largish sheets or two pieces of veneer joined in the middle with gummed veneer tape. I had previously flattened the veneer using water/glue/glycerin/denat alcohol mix, but had thoroughly I thought dried the veneer over a week. The next day after adhering the veneer sheets I found that the seams had opened - apparently the heat from the iron caused the veneer pieces to shrink away from the seam. I'd consider using the hot iron trick to edge glue veneer, but not on a panel of any size.

Re: Thinning Titebond

#15

Re: Why?

TomD

What about thining it with acrylic? I have this bottle of Acrylbond, I throw at anything. Want to bond regular drywall compound to paint on the ceiling, throw in some AB. Want to make a small amount of bonding sealer. Throw it in. Want to thin croncrete premix to close the gaps between my sofit, and the barker brick of my wall. Thin it to a working consistency with AB. Not too sure what one would get, for one thing this stuff sets pretty quickly itself, but I bet it would be interesting.