Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

? About Using 1/4" Ply To Make A Box...

Posts

? About Using 1/4" Ply To Make A Box...

#1

? About Using 1/4" Ply To Make A Box...

Derek Arita

This may be one of those dumb questions... I want to make a simple box to fit into a shop drawer to hold some parts. I have some left over less-than-1/4" ply that I'd like to use. How would you suggest I join the edges? If there's enough surface area to do butt joints that will give me reasonable strength, I'd do it, just for simplicity sake, but I don't know if it would work. What are your suggestions?

Re: ? About Using 1/4" Ply To Make A Box...

#2

Re: ? About Using 1/4" Ply To Make A Box...

Henry (Raleigh NC)

If your boxes can tolerate it, use inside corner blocks for more glue area - these are utility boxes right?

Henry

Re: ? About Using 1/4" Ply To Make A Box...

#3

Got a table saw?

John in NM

I'd do a finger joint, fingers the width of the saw blade. Quite easy once you get the jig set up and it makes a nice strong joint.

Re: ? About Using 1/4" Ply To Make A Box...

#4

Finger Joint

Mark Mandell - Gone Round In New Jersey

or Box Joint? :D

Seen them called both ;)

Re: ? About Using 1/4" Ply To Make A Box...

#5

Re: Got a table saw?

Barry Irby

finger joints are a classic and will work well for this.

If you don't want to get that fancy, how about rabbet joints? Rabbet about a third of the way through and then glue them up. You could also let one side run past and put glue blocks into the outside of the corners.

Or, you could glue them up with titebond or whatever and then "caulk" the inside corners with hot melt glue.

Really depends on how much of a beating the boxes will take in use.

Re: ? About Using 1/4" Ply To Make A Box...

#6

Re: Got a table saw?

Derek Arita

Box joints is what I was thinking at first, but for what this is, that seems like a lot of trouble to go thru...still, setting up the jig could be good practice for me. I'm just worried that with such small plywood fingers and cheap ply I might add, I could get a lot of tear out. Anyone ever do this?

Re: ? About Using 1/4" Ply To Make A Box...

#7

Yup

Mark Mandell - Gone Round In New Jersey

Made dividers for a friend's electrical and plumbing "parts" drawers. Box joints at the corners, dadoes on the rims, half-laps at the crosses. Only the corners were glued so he could remove partitions to reconfigure the interior spaces.

Re: ? About Using 1/4" Ply To Make A Box...

#8

I've done it with baltic birch...

John in NM

So tearout was less of a problem than with something like fir plywood. But your jig should provide backing for the plywood and prevent much tearout. I usually make a new jig each time, that helps keep the jig in good shape to support the wood around the cut.

Re: ? About Using 1/4" Ply To Make A Box...

#9

Duct tape

Bill Houghton, Sebastopol, CA

You might try some of the metal corner bead sold for finishing drywall corners, pop-riveted to the plywood. Be sure to clean off the sharp edges of the cuts.

Re: ? About Using 1/4" Ply To Make A Box...

#10

Hot glue works


Re: ? About Using 1/4" Ply To Make A Box...

#11

Rabbet Joint

brian greene

I've made dozens of small utility boxes, some as small as 3/16", using rabbet joints made on the table saw, the router table or by hand with a plow plane. Some receive very hard use. Not one has failed. Fast and easy. Need more durability, go with finger joints.

Re: ? About Using 1/4" Ply To Make A Box...

#12

Re: Got a table saw?

Bruce, a MN Galoot

you could also put small glue blocks in the corners, if you don't need that corner space.