Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

OT - running a gas line

Posts

OT - running a gas line

#1

OT - running a gas line

Bill Houghton, Sebastopol, CA

I'm running a line for a little gas heater. I haven't looked up the demand yet, but the similarly sized heater in our living room only requires 1/2" pipe for the eight foot run from the main supply pipe.

However, this heater is on the far side of our (1500-square-foot) house from the gas meter. Rather than calculating the distance from the meter* and the pipe size requirements, I'm running 3/4" pipe, the size of the incoming pipe from the meter, from the point at which I tapped the existing lines.

But I'm thinking that, if the gas demand for the new heater supports it, I may drop down to 1/2" for the last, short bit through the wall and into the room. It gives me more flexibility in selecting a gas valve. Is there any reason that I should stay with 3/4" all the way to the valve?

*Like most older houses, the gas lines under the house are not exactly rationally laid out; there's a certain amount of wiggle and wander as they make their way around.

Re: OT - running a gas line

#2

Size Matters

Mark Mandell - Gone Round In New Jersey

While your new line may be overkill for the "current" heater, you might have issues if you wish to either enlarge the unit later or add another gas-using item. Since you're piping with 3/4 I would go all the way to the valve with 3/4 and then do your step-down after the valve. That way, later mods after the shut-off are a no-brainer.

Re: OT - running a gas line

#3

Re: Size Matters

Joseph Mulherin, sr

Mark is correct in his layout... and I am a retired Pipefitter/Plumber.

It also has to comply with the local gas company requirements,

but I foresee no problems with the 3/4".

Re: OT - running a gas line

#4

Re: OT - running a gas line

Alan in Little Washington (NC)

Based on your Kalifornia location, I would bet you can't run gas line without a permit and maybe a license, too. Also, if you do it yourself, and your house blows up, your insurance may not pay.

If you still plan to do it yourself look online for a gas line piping spec sheet or calculator- selection of pipe ID is based on device demand, pressure, length of run and other devices on the line. Also, codes for pipe type differ by state/municipality- in some places black iron is the only one authorized, other places you can use copper or stainless flex designed for gas (yellow stripe or yellow jacket, etc.)

Re: OT - running a gas line

#5

Permit, yes; license, no

Bill Houghton, Sebastopol, CA

At least in my town, homeowners are allowed to do pretty well everything on their own houses with a permit - which I have.

There are some choices of pipe, but black pipe is preferred, and that's what I'm running.

Re: OT - running a gas line

#6

Re: Permit, yes; license, no

Dick Coers

Go to a professional supply house for your materials if you can. The stuff at the BORG is horrible quality in the threading. I tried running some air lines in the garage, and had air leaks in several places. If you can't get better quality, I preferred paste pipe dope over tape.

Re: OT - running a gas line

#7

Jason Roehl in Lafayette, IN

Pipe dope.

Jason Roehl in Lafayette, IN

If running gas line, there is a pipe dope rated (required, I think) for gas. I found that it worked better on all my air fittings than the regular pipe dope. Apply liberally to the male threads (I like to "scrape" the dope off the brush perpendicular to the threads), then screw the fittings together. Tighten securely, then use a soap solution to check for leaks after assembly.

Jason

Re: OT - running a gas line

#8

Re: Permit, yes . . .

Mark Mandell - Gone Round In New Jersey

Inspection . . also required.

In my area, a new gas line must be pressure tested by the inspector before being put into service. Shut-off to shut-off is taken to (IIRC) 100psi and then checked 24 hours later. Any drop and you can go back and find the leak. Bubble test is fine for air but not for a fuel gas.

Black pipe for fuel gas takes the Blue Goop.

Re: OT - running a gas line

#9

PSI

Mark Mandell - Gone Round In New Jersey

mentioned is for new system/ whole structure. Additions to existing are tested at 15 psi

BTW Make sure your fittings are rated for gas. A water plumbing valve good to 250 PSI is not necessarily rated for gas at 5 psi.

Re: OT - running a gas line

#10

That is a bit surprising

John in NM

Gas work is the one thing that has to be done by a licensed contractor out here in the back of beyond where everyone builds everything wildcat anyway :D :D :D

Kinda neat that CA lets you do your own.

Re: OT - running a gas line

#11

Gloating

Bill Houghton, Sebastopol, CA

AND the inspector in our little town is very supportive of homeowners who do their own work. That's not to mean he lets me get away with stuff, but he's not harsh. Not all inspectors are supportive that way.