Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Skil HD77?

Posts

Skil HD77?

#1

Skil HD77?

Charles Jackson III

I looking at replaceing my Skil homeowner grade circular saw because it is on its last legs. I am wondering is a Made in USA Skil HD77 off E-bay a good choice? I will be using the saw for framing and general carpentry projects.

Re: Skil HD77?

#2

Worm-drive

Mark Mandell - Gone Round In New Jersey

Great, maybe required, for busting up wet 2x material or going through LVLs and microlams, but the weight of the beast will get to your wrist and elbow in fairly short order.

If you can set aside the "Arg-Arg!" macho contractor factor and are cutting reasonably dry framing stock and sheet goods, I strongly rec the PC 6" Saw Boss. A 6" saw that will fly through sheet goods, 2x4/6 df and even treated lumber and decking with ease and won't beat you up in the process.

Re: Skil HD77?

#3

Re: Worm-drive

Barry Irby

My understanding is worm drive saws are typical for framing contractors in the west and in the east we use direct drive saws. Mark is right. The worm drive saws tend to be powerful, but really "nose" heavy. Tear your arm out of the socket by the end of the day Heavy. (I am about 5' 7" and 165 lbs and framed hundreds of houses "back in the day" but a worm drive saw would whip me now) Unless you are turning pro I would look at a direct drive saw. In fact, I have just downsized to a 6 1/2" and like it a lot. Have not used it much, but it seems entirely adequate. (going from a 7 1/4" to a 6 1/2" does not "cost" even the 3/8" you would think. Apparently they make the motor housing smaller and it only costs about a 1/4" on the depth of cut.)

Re: Skil HD77?

#4

Re: Worm-drive

Charles Jackson III

I went to school for building construction so I plan on doing carpentry work for a living.

Re: Skil HD77?

#5

Second Consideration

Mark Mandell - Gone Round In New Jersey

If you're going to be framing for a living, I'll pass along that guys in my area have passed up on the higher quality, more expensive saws for a very simple reason: They don't bounce well when dropped off the roof. You drop that big-ass pricey worm off the second story, it's toast. Goes right in the dumpster.

I see very few pros using "hand" saws for cuts-to-length; chop saws have taken over that job as they are much faster and more accurate which translates to more and better quality work product. Rip a 2x10 to a 2x9, the worms are just fine used at ground level. Cutting sheet, the 6" PC is better and faster.

But after all, it is your money ;)

Re: Skil HD77?

#6

Re: Second Consideration

Charles Jackson III

My shop teacher did not like using chop saws, for rough carpentry.

Re: Skil HD77?

#7

Re: Second Consideration

james runchey

I built many homes before I retired 21 years ago and I always used a 6 1/2" wormdrive Skilsaw. It was large enough to the job, but not as heavy as the 77. When i started out I had a conventional sidewinder and on one of my first jobs I had to rip a bunch of 2x8s.and didn't get thru them all before the saw burned up. made me a believer in the worm drive power. Another job we had was to replace the roof rafters, shingles, sheathing, everything right down to the ceiling joists. I took the wormdrive with a carbide blade and made cuts from the peak down to the eaves every 16" cutting thru 2 layers of shingles and 1" sheathing which we then peeled off leaving nothing but the rafters. The Skilsaw ran thru this with no effort at all. I, for one am sold on the wormdrive.

Re: Skil HD77?

#8

Re: Skil HD77?

Robby Wright in San Marcos, CA

Charles - I have owned a Skil 77 wormdrive saw for over 40 years. I'm on my third one now - the first two I was given by my father and grandfather. Both had been dropped without much more damage than a chipped casting or bent shoe. The 77 is a brutal powerful saw, but is capable of fine work as well. It is heavy - that wormdrive transmission weighs something, but it doesn't stall easily in wet wood and will keep cutting all day long. Get a rafter hook to replace the top handle and you will be able to hook it over framing lumber when you are up high.

There are two things I love about the 77. First, the blade is on the left side of the saw. I hold my saw in the right hand and having the blade on the left makes it easier to see where I am cutting. Second, having the handle in-line with the blade makes it easier to steer. Add a decent carbide blade and you have a very good saw.

The advice to also look into a chop saw or sliding compound miter saw is good advice. You will tend to cut many pieces to length before you assemble them and the chop saw on a proper stand can speed that up.

Good luck with your new career.

Re: Skil HD77?

#9

Re: Second Consideration

Bill Houghton

"Rough" carpentry is an interesting term. You'll still get finer framing if your cuts are square and the right length. My contractor son converted me on this subject; he uses his chop saw all the time for framing work. Faster than lining up a cut with a hand circular saw.

Not worth it for one cut, but, if you're working all day on a framing project, you might try it.

Re: Skil HD77?

#10

Re: Second Consideration

Charles Jackson III

What the model number on the Skil 6-1/2'' and much lighter it is than the 77?

Re: Skil HD77?

#11

Re: Skil HD77?

Charles Jackson III

I been using a circular saw for rough framing for so long, I draging out the chop saw.

Re: Skil HD77?

#12

Jason Roehl in Lafayette, IN

I agree.

Jason Roehl in Lafayette, IN

I have the HD77 and love it, even though I don't frame for a living. Yes, it is heavy, but there is a magnesium-housed version that is a bit lighter (HD77M)

The power and one-handed control through the cut are excellent. Set the blade to the proper depth (just exposing the gullets), and it speeds through sheet goods. I'm also a rightie, and I really like the left-blade setup--no more hunching over the cut to see the line--though it does mean you get more sawdust thrown your way.

I do know a framer who won't let any of his workers make a cut on framing lumber without using a square as a guide. I think that's good practice, but if I were making a bunch of repetitive cuts, I'd use a chop saw with a length stop set.

Jason

Re: Skil HD77?

#13

Re: I agree.

Charles Jackson III

Thanks guys for the advise.

Re: Skil HD77?

#14

Re: Skil HD77?

Justin Szeliga

When you buy a saw like a Skil 77 or, even better, heavier, more manly than a rugby team, an 8 1/4", you buy a profession saw that is capable of being repaired. Handles, base plate, everything can be replaced. When you drop a Skil wormdrive you most likely will be able to fix it.

What I like about them is the steadiness of the cut, the saws are so goddamned heavy that they track very well, & when cutting lumber held in your hand they drop right through the cut, no pushing. All that weight has a benefit too. They are also good about kickback, all that weight wants to keep moving forward & they are, in my experience harder to kickback than a sidewinder. Well, not my DeWalt cordless, but that hasn't the strength to kick itself back.

Re: Skil HD77?

#15

Re: Skil HD77?

Charles Jackson III

Been looking at getting a Skil 6-1/2'' Wormdrive.