Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Using A New Dado Technique...New To Me...

Posts

Using A New Dado Technique...New To Me...

#1

Using A New Dado Technique...New To Me...

Derek Arita

OK...So I was trying to figure out a different way to do some dados, other than on the TS. I liked some of the jigs I've seen, but didn't want to buy another jig. I already have a Festool OF1400 and guide rail, so I figured out a way to do the same thing that jigs do, without the jig. The technique can be done with other routers using guide rails. I'm sure a lot of you have already figured this out, but this is new to me, so I thought I'd share...

I set up the router as usual, using the router "Guide Rail Stop", which is Festool's name for the router guide rail adapter. Since I'm using a 1/2" upcut bit for a 3/4" dado, I use a 1/2" gauge block to space the router exactly 1/2" from the rail edge.





I then run the first pass. For the second pass, I replace the gauge block with a piece of the actual material that's going to fit into the dado, along with a .008" feeler gauge piece, for glue spacing and plywood imperfections.



[URL=http://imageshack.us/photo/my-images/5/img0612wc.jpg/][/URL]

After making the second pass, I get a dado that is consistently just the right size for that piece of plywood.



Comments?

Re: Using A New Dado Technique...New To Me...

#2

Re: Using A New Dado Technique...New To Me...

Joseph Mulherin,sr

I think you have done a very good job in figuring out this method.

Others have done such before and it is necessary to not cut exactly

in the first cut using a 3/4" bit because of the difference in the various

grades of plywood from different suppliers. Your technique is excellent.

Re: Using A New Dado Technique...New To Me...

#3

Re: Using A New Dado Technique...New To Me...

Derek Arita

Glad you like it. It's so simple, I'm sure a lot of others here have done the same. While I was researching some of the dado jigs, a light just went on in my head. All of the "tight dado" jigs seemed to use a gauge block and a piece of material the dado was to fit, so those two pieces must be the key. I think it will work great as long as your gauge block matches your bit size.

Re: Using A New Dado Technique...New To Me...

#4

Bob

Re: Using A New Dado Technique...New To Me...

Bob

Works for me. Thanks for sharing.

Re: Using A New Dado Technique...New To Me...

#5

Re: Using A New Dado Technique...New To Me...

John Lucas

For shorter Dado's I use a sort of T square wooden jig I built. The router rides in the middle using bushings. I cut through the first part of the jig so all I have to do is line up this notch with the marks and clamp it down.

For longer dados I use one of the dedicated plywood clamps. I did purchase dedicated plywood router bits that are slightly undersized. They work great.

Re: Using A New Dado Technique...New To Me...

#6

Re: Using A New Dado Technique...New To Me...

Jason Waters

Derek,

The pictures are great! Looks like a nice precise setup to cut dadoes. You adapted your Festool guide to your use very well. Some of the best jigs/setups I have are "adaptations".

I always just used a straight edge guide (or even a straight board or a level! in a pinch) across the plywood. And then I just cut across with a smaller bit (usually 5/8 for 3/4 and 3/8 for 1/2) and then reset the "straight edge" over to make the next cut. Of course, you don't get the great gauge block setup you have doing it the way I described. And you have to make sure the router doesn't wander off the straight edge guide! Your way is definately better.

Now, I nearly always use my tablesaw and dado set.

This just shows (or reminds us) you don't need a heck of lot of equipment for woodworking, it just takes a little more time.

Now, what are you going to build with the money you saved not buying that jig?

Jason

Re: Using A New Dado Technique...New To Me...

#7

Re: Using A New Dado Technique...New To Me...

Derek Arita

Glad you brought up the table saw thing. That's all I used to use for dados and rabbets. Just recently, I thought I'd try doing it with a router. Once I did, I found I got a much cleaner, more consistent cut with the router. The dado bottom and edges are precise, which makes the joint, that much better.

Even though I used a really good, adjustable dado blade, the comparison was pretty obvious, especially on plywood that is not perfectly flat or consistent. I know it can be easier with a table saw...just set the blade and fence and run your stock. That said, there are lots of times when your stock dimensions make that method unsafe. Anyways, I'm now a convert.

Re: Using A New Dado Technique...New To Me...

#8

Re: Using A New Dado Technique...New To Me...

Kelly Craig

With my dado jig and any of my routers, I can make dead on dados across an eight foot shelf in minutes. Once the lines are laid out on the boards, it takes about forty-five seconds, at most, to set up for each dado. Since the jig sit exactly on the dado lines and the patter bit follows the jig, one pass up and one down and I'm ready to move on.

Re: Using A New Dado Technique...New To Me...

#9

Re: Using A New Dado Technique...New To Me...

Jason Waters

Derek,

Those are good points, odd shapes (I use a router too, with a straighedge clamp on) and warped plywood, and pieces that are bowed, particularly if an inside cut.

I will say that if you aren't spending the money for a good dado blade, a router is definately the way to go. Also the router is more portable, and can taken elsewhere to do work a lot easier.

Jason