Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Ripping on TS safety question(s)

Posts

Ripping on TS safety question(s)

#1

Ripping on TS safety question(s)

Joe in a Cleveland suburb

Hello.

I need to rip some pieces of plywood. They need to have a 22.5 degree bevel on one edge and I am wondering about a couple things.

The finished width will be 5" and the length is about 24".

I am concerned about safety doing this.

When I rip the bevel, should the blade be tilted towards or away from the rip fence - I've never been too sure about this. :\

Also, would it make sense to rip the pieces wide, say 5-1/2" with a bevel, then put the beveled side against the rip fence and rip to final width?

Safety with my 1023SL (w/splitter) is always on my mind. I've never been too sure on the safest way to rip a bevel.

I know these are rather newbish questions, but the older I get, the more concerned with safety I get and the more I question myself ...

Hope I'm asking this right and making sense.

The pieces are for a corner cabinet thingy I am making.

Thanks.

Re: Ripping on TS safety question(s)

#2

JL

Re: Ripping on TS safety question(s)

JL

My take - always have the bevel you are cutting on top of the blade. You don't want anything trapped between the blade and the fence.

The idea of cutting the bevel and then ripping to width works for me. It's what I often do.

Re: Ripping on TS safety question(s)

#3

Re: Ripping on TS safety question(s)

Bill Howatt

The loose off-cut should not be between the workpiece and the fence. However, in lots of cases this is unavoidable and if it is, then be sure you keep out of the kickback line of fire. I believe your saw is a left-tilt and if so, it is OK.

Cutting the bevel and then the finished width is what I would do since you are more likely to get an accurate width because it is much easier as a rule to set the fence accurately for the 90 degree cut than the bevel. Make sure when you do this cut the long edge of the bevel is up; if it is down it may slide under the fence.

Bill

Re: Ripping on TS safety question(s)

#4

Re: Ripping on TS safety question(s)

Hal

IMHO both JL and Bill have given you good advice. General rule; if you have a left tilt blade, the fence should be on the right side of the blade and if you have a right tilt, the fence should be on the left side. There may be exceptions, but as said, be careful and keep out of the "line of fire". Hal

Re: Ripping on TS safety question(s)

#5

Re: Ripping on TS safety question(s)

TomD

If it leans to the left, the fence goes on the right, that way, the rotation of the blade holds the workpiece down on the table, and over against the fence. If you want to trim the piece for width, or cut a bevel on the second edge, then you can, go ahead, but it is better to have the thin edge high, so it does not jam under the fence.

One of my rules for table saws is I don't do it if it can't be safely done (which this can). But if you want to escape injury, never let yourself drift into doing iffy things on the saw. It isn't professional, if you care about that. And a lot of pros are missing digits.

Kick back is very dangerous. A a 10" blade doing 5000 rpm, has a surface speed of 218 feet per second. If your piece comes off the saw at that speed, as small pieces can, the projectile is lethal. When I got into archery, 218 fps was about tops, and bows shooting arrows that fast had killed all the game on earth. An arrow would have a weight of about 1 oz +. At that weight and speed it develops an energy of 40 foot pounds. A 22LR bullet does about 110 foot pounds or about what a piece weighing 3 ounces would hit with at that speed. I have been hit by much heavier pieces, and they did slow the blade speed down a little, but they were moving like hell. It really hurts.