Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Plywood Box & Epoxy/Fiberglass

Posts

Plywood Box & Epoxy/Fiberglass

#1

Plywood Box & Epoxy/Fiberglass

tom

I am resurrecting this project after I first poste din May. My goal is to fabricate 2 cases to be used for carrying our bike which is a tandem that breaks down. My sizes,for air travel, are 10" X 26" x 26". To purchase the $ is about $400+ each. So I wish to build.

My original idea was 1/4" ply boxes with reenforcements and then use fiberglass/epoxy system inside and out. I started looking at the idea of aluminum extrusions but after doing the math I came up to about 25lbs. per case with almost 15lbs being the enxtrusions.

So now I am back to the original idea. I have used West Systems epoxy for other project but have just experimented with epoxy and cloth.

I have looke online for info on this sort of project but have come up with nothing.

Advice would be great. Also any idea of a way to join the lid to the case, there is an extrusion for this which I my use but would be open to ideas.

Thanks!

Re: Plywood Box & Epoxy/Fiberglass

#2

Jesper, Denmark

Re: Plywood Box & Epoxy/Fiberglass

Jesper, Denmark

If the object is to keep it light, rigid and strong, I would look at using 1/4 inch divinycell or similar foam board intended for glass laminate lay-ups. It is easy to include stiffening ribs and glass over.

If flight security access does not prohibit this, a flat side panel screwed or bolted onto an internal rib is simple to make.

Re: Plywood Box & Epoxy/Fiberglass

#3

Re: Plywood Box & Epoxy/Fiberglass

tom

Jesper,

I will look into this material. Interesting that you would reply as I am making these cases for our first European cycling trip which wll be in Denmark!

Re: Plywood Box & Epoxy/Fiberglass

#4

Jesper, Denmark

Re: Plywood Box & Epoxy/Fiberglass

Jesper, Denmark

Lots of bicycles and bicycling here - and no significant hills. It could be a bit rainy, though. Youth Hostels are a good solution to overnighting and there are campgrounds everywhere.

http://www.danhostel.dk/content/us

Re: Plywood Box & Epoxy/Fiberglass

#5

Re: Plywood Box & Epoxy/Fiberglass

TomD

I've don lots of wood, epoxy, glass, carbon. So if you have any specific questions, there probably aren't any haven't heard of before.

I also make bike frames so I am well familiar with touring issues. But I do not have much experience with tandems, just rode one. I would like to build one, because there are a lot of riders in the family. Biggest problem with boxes is what to do with them when touring. Obviously they can be stored, other alternatives are making them part of the system, like the Bike Friday trailer. I tend not to use boxes, which is the third option.

Re: Plywood Box & Epoxy/Fiberglass

#6

Re: Plywood Box & Epoxy/Fiberglass

tom

Tom,Thanks for your reply. I could use help with a few questions. Is there some info availale that would show how to do the outside of the box with the epoxy/fiberglass? Also in order to cut down on weight what would you think about just doing the inside corners of the boxes interior?

Thanks in advance!

Re: Plywood Box & Epoxy/Fiberglass

#7

Here ya go *LINK*

Bruce, a MN Galoot

This is from the West System site. While it might not be a pannier, it is a box.


Building a box

Re: Plywood Box & Epoxy/Fiberglass

#8

Re: Here ya go

tom

I had seen that article but where I need help is how to "form" the fiberglass around the outside corners. I think I am clear on how to do the interior.

Re: Plywood Box & Epoxy/Fiberglass

#9

Jesper, Denmark

Re: Here ya go

Jesper, Denmark

Do the nside first. Use a roundover bit in a outer to make the shape of the outside joints and corners. Do not attempt to cover the sides and bottom in one go - it will be a mess.

Use visqueen on top of the fibreglass and a squeegee to smooth the lay-up- The wet cloth stretches enough to be able to form it around the corners, leaving a little excess glass on the bottom to be sanded when dry.

The visqueen eliminates having to deal with the sticky mess of glass and epoxy and peels of easily when the epoxy is cured.

Do not forget to paint the finished product. Epoxy is not UV resistant and needs a UV impervious coating.

Re: Plywood Box & Epoxy/Fiberglass

#10

Re: Plywood Box & Epoxy/Fiberglass

TomD

"Tom,Thanks for your reply. I could use help with a few questions. Is there some info availale that would show how to do the outside of the box with the epoxy/fiberglass?"

- You should always attempt to do as much of piece at once as you can. In this case it would be 5 sides. So you run your router bit, and round over the corners, you will need round overs about as round as a pencil or a dime. Depends on the drape of the material you are using. I would probably use something in the 4 oz area.

- So imagine a table top you have thrown a table cloth over. That is how you set up your box, and how you drop your cloth on it.

- You have 3 different type of corners to do. 1) the three edges to the table top, these the material just falls over; 2) the three vertical edges, these the material is cut back from, but you have the option of trimming one side back and folding the other over, keep all folds back from the corner. If you chose to cut back from these verticals, make some bias strip to cover them; 3) The 4 corners, these the material is cut back from, and you cut out at least 10 round pieces, half of about 4.5". and 3.5".

- After routing and sanding, you will have some rough spots and probably some holes. Do not assume the cloth will bridge anything. You have the option of patching the problem areas and working on them till they are perfect, then when all is dry and smooth, you glass. I prefer to jump right in and the instructions that follow will deal with that approach, as well.

- When you are ready to go, you make up some putty (bog), and some clear. You have a 2" chip brush and a squeegee on hand. You dab any areas you need to fill will light epoxy resin, then you smear on bog. Leave the bog a little high, as it will disolve in. Everything has to be done fast, so as to keep ahead of the cure.

- Drape the material like the aforementioned table cloth over the part. Cut out the verticals and the corners. start wetting out the cloth with epoxy and squee.. and move the epoxy around so it fully wets the top cloth. Never leave puddles to harden, always scrape back to the surface of the cloth, but having done so the epoxy will sink in, and you will need to add more and srape off over the cloth again.

Work epoxy over the the top edges and down the faces wetting the glass as you go, but be careful not to splash it all on the ground. The corners will dry out the worst, so keep wetting them with the brush, and push them over with the squee.

When eventually you get the cloth down and filled, pick up your bias strips and do the vertical edges, but do no go all the way up to the corners. You can use small amounts of bog to smooth out joint areas so the cloth will lay down better. once the vertical side corners are done, you do the corners with the circles. Patch bog under, around the edg of the cloth, and on the very corner. drop the circle over the corner.

There is a trick to orienting the corners, which consists of looking at the corner with your eye entered over it, the way you would do, if you were looking through a cube from corner to corner. The circle has the fibers of the cloth running 0/90 in it, place those fibers so the are centered over the faces, and not the edges that run from the corners. If you don't get it right, no problem, just offset the circle 60 degrees and try again.

Once the circles are in place, dab them down, and wet them with the end of the brush, alternating some painting strokes. Then immediately slap the second patch on.

" Also in order to cut down on weight what would you think about just doing the inside corners of the boxes interior?"

That will work fine, assuming you made the box strong enough, but as far as making the corners strong, it does not mater that you glass the inside of the bog, just the corners. And you can even then get away with just coving the inside corners, though glass is a big upgrade. Use bias cut strips. You cove with bog, then you put the cloth in. Do it all at once, and wet. Do not bog, then sand, then glass.

The method described is the "dry method". this does not seal the plywood before the glass is put on. This means the plywood can offgas into the job. So select a time to do this job when the temps are cooling, or stable, and the barometric pressure is relatively stable.

Re: Plywood Box & Epoxy/Fiberglass

#11

Re: Plywood Box & Epoxy/Fiberglass

tom

TomD, Thanks for the info!

It is very clear. Just 2 short questions. On the box interior my thought was to use a 45 degree glue block then use fiberglass tape on these inside corners bridging the top and the side. Will this work as oppoesd to coving? The circles for the corners, you mention 2 sizes. Which one goes down first.

Again thanks for your help!

Re: Plywood Box & Epoxy/Fiberglass

#12

Re: Plywood Box & Epoxy/Fiberglass

John M in Mid Mich

Tom:

When I built mine I contacted the cloth manufacturer and asked what the minimum radius was for going around a corner. I then use a round over bit on the router to get that radius on all my outside edges. I think it was 3/4". I did not radius or glass the inside corners, although you could create some cove material so that you could glass them.

John

Re: Plywood Box & Epoxy/Fiberglass

#13

Re: Plywood Box & Epoxy/Fiberglass

AlanWS

Except for the shape, your box sounds like a stitch and glue kayak construction. These are made from plywood cut to shape, covered with fiberglass-epoxy, and connected edge to edge.

Among other places, clcboats has a lot of information on the process (and will sell you everything you need.)

Here is a link to a set of videos showing all the steps:

http://www.clcboats.com/shoptips/building-stitch-and-glue-kayak/

Re: Plywood Box & Epoxy/Fiberglass

#14

Re: Plywood Box & Epoxy/Fiberglass

tom

Thanks, I forgot about them as a supplier. I went on their site and will be ordering this week.

Re: Plywood Box & Epoxy/Fiberglass

#15

Re: Plywood Box & Epoxy/Fiberglass

TomD

"TomD, Thanks for the info!

It is very clear. Just 2 short questions. On the box interior my thought was to use a 45 degree glue block then use fiberglass tape on these inside corners bridging the top and the side. Will this work as oppoesd to coving? "

In some cases the wood alone would be fine. Structurally what you suggest would be fine. Getting cloth to lie down on a solid base is probably iffy. Normally getting the cloth to lie down is easiest if it is vac bagged, which is crazy in this case, or if it is in a wet cove. If you want to save money, you can use a smaller piece of wood, and then bog over that. It is amazing how little hardness under the cloth will cause it to lie poorly. I have done large areas where if you did not insert some wood, you not only had cost issues, but fire problems. Obviously not an issue on this scale.

"The circles for the corners, you mention 2 sizes. Which one goes down first.

Again thanks for your help!"

Normally the big one. If you put the small one down and bogged it, that would work also. One's immediate thought is that the larger one on top would help smooth things out. and the smaller one on top will not leave a perfect surface. There is always more than one way to do things. I have been at this 30 years, and some of my early work failed here and there (after 20 years out of doors) as in only normal. So I learned to be satisfied with a few spots where the first wet-out results were seemingly crude, but the glass is perfectly intact. I also look for methods where the smoothing can be done without sanding, as this leaves full thickness glass, and the dust is very bad stuff. But as I say there are many different ways to proceed.

By the way, what I am describing is a method where all the work described is done in one wet, all the layers go down at once, on the outside.