Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

French Cleat Question...

Posts

French Cleat Question...

#1

French Cleat Question...

Derek Arita

I have a completed cabinet that I want to attach to a wall. It will mount over a toilet. I want to use a French Cleat, but the back of the cabinet is assembled. Can I simply attach the cleat to the back of the upper cabinet and hang it on a corresponding cleat, attached to the wall. I know I'd have to include a spacer board on the bottom, rear edge to keep the cabinet plumb. Will this work?

Re: French Cleat Question...

#2

Dale Lenz

Re: French Cleat Question...

Dale Lenz

The best I can read into your post, it should work. Once I used a french cleat using nails as the fastners, thats a no-no, the weight of the cabinet and it's contents, hand planes came off the wall onto the the contrete floor. I was lucky, the planes where not damged. If I ever use french cleats again, I will use screws.

Re: French Cleat Question...

#3

Re: French Cleat Question...

Derek Arita

Screws for sure! I'm used to seeing the cleats being integrated into the cabinet back, but since the cabinet was already assembled without the cleat, I want to add it externally. Hope it will work!

Re: French Cleat Question...

#4

Dale Lenz

Re: French Cleat Question...

Dale Lenz

Just finishing up 4 military sword display cases to be shipped to different customers. It was suggested that I use a french cleat for hanging the display case if the customer choose to do so. Did not like the idea of the customer fastnering the wall cleat to their wall, so I went with routered key holes.

Re: French Cleat Question...

#5

Re: French Cleat Question...

Bill Tindall, E.Tn.

use a thin metal one from Lee Valley

Re: French Cleat Question...

#6

JL

Re: French Cleat Question...

JL

Z-clips are metal and quite thin.

If you do go the French Cleat route, might I suggest having a French Cleat between two vertical edging pieces? That way you won't have a visible "hole" on the back of the cabinet. You also won't need a spacer bar at the bottom - unless you want one.

Re: French Cleat Question...

#7

in favor of cleats

Bill Tindall, E.Tn.

So-in-law worked for a time at a shop that designed and built stuff like lobbies and conference rooms. It was standard practice to hang cabinetry off lobby walls with the metal cleats. Unlike key holes there is no precise aligning to be done. Odds are that two screws can be lined up with studs for a cabinet of any size. The metal cleats enable the cabinetry to lay close to the wall. What's not to like?

Re: French Cleat Question...

#8

Re: French Cleat Question...

Hal

I use 3/4" ply for the cleats - whatever I have on hand. Of course be sure to find at least two studs. I use a minimum 3" screws, 4" probably better. Attachment of the cleat to the cabinet is another matter. Are you going to run screws thru the cabinet back into the cleat? That would be preferable except for appearance - perhaps use trim washers? Your basic idea is the same as I have used. Hope it works out OK. Hal

Re: French Cleat Question...

#9

Dale Lenz

My reasons for not using the cleat

Dale Lenz

Let say the owner of the sword case decides not to hang the case on the wall but to display on a shelf or other flat surface, may hang on the wall in the future. So the new owner of the sword case puts the wall side of the cleat up someplace for safe keeping. The time comes to find the wall cleat, and guess what?? I had no desire to build/design into the case a way to keep the wall side of the cleat with the case.

The way I transfer where to put screws/anchor nuts into the wall is to lay something like paper between the two key hole's entrance voids and mark. Transfer the marks to the wall, works great.

Re: French Cleat Question...

#10

Re: French Cleat Question...

Derek Arita

Yeah...I've got mounting strips already built into the top and bottom of the back, so I'll screw into those with washer head screws into the cleat. I'll use regular 3" flat head screws on the wall cleat. I was, however thinking of using some 5/8" plywood cleats.

Re: French Cleat Question...

#11

Re: French Cleat Question...

Hal

5/8" or even 1/2" should work just fine.

Re: French Cleat Question...

#12

Sure, I've done it

Bill Houghton, Sebastopol, CA

Be sure that the cleat on the cabinet (and the wall) are firmly fastened. Integrating the cleat into the cabinet allows for a stronger attachment to the cabinet, but it's not too late. Screw into the top and sides of the cabinet, and you should be fine.

After all, you're probably not storing Chevy 350 motor-driven hair curlers or depleted uranium cosmetics; so not much weight.

Re: French Cleat Question...

#13

Re: French Cleat Question...

Jerry Roberts

If you are building new stuff to hang, what I did a couple years ago when I built my shop cabinets is to inset the back abt 3/4 in or the thickness of the cleat. That way there is no gap between wall and cabinets and no lower support to install. The only problem is the cleat only extends to the edge of the cabinet so one cannot slide it to suit. What I did on others is to cut notches in the side so the cabinet is able to slide along the length of the cleat on the wall.

Re: French Cleat Question...

#14

Re: French Cleat Question...

Stuart Johnson

I made my cabinets similar but cut cleats about two inches shorter than the width of the individual cabinets. This gives plenty of support but also the ability to adjust them.

Re: French Cleat Question...

#15

Re: My reasons for not using the cleat

William Duffield

Such a design doesn't seem too difficult to me. The cleat would be stored in the same location as it fits when screwed to the wall. Two pairs of rare earth magnets should hold it in place until you need to remove it and screw it to the wall. If your case back is too thin to hold magnets, you could put them in the ends of the cleat and on the insides of the case side walls.

Re: French Cleat Question...

#16

Re: French Cleat Question...

Phil

That is exactly how I hung the chisel cabinet pictured above. Watch out for the vent stack which is probably dead center in the wall behind the toilet: would not want to puncture that in the process of fastening the cleat.

Re: French Cleat Question...

#17

Re: French Cleat Question...

Derek Arita

Excellent point! I will steer clear of the vent. Didn't even think of that, but I'm only into the studs, so I should be fine.

Re: French Cleat Question...

#18

Re: French Cleat Question...

TomD

That will definitely work. Other than the fact that there is "nothing" holding one cleat to the other, There are more screws, etc... holding this stuff together than you can shake a stick at. If I was doing this, and I have plenty of these cabinets around, from gross to nice. The cleat would be screwed at top, and on the ends. Right there there are 3 screw holding the thing up. I took apart my dad's kitchen, a heavy upper cabinet, massive, that fit around an inside corner, was held by only 2 nail. The thing about French cleats is that it is an elegant way of permitting overbuilding. One would be amazed what can be held to a wall with one finishing nail, but with a French cleat you never need to find out.

Re: French Cleat Question...

#19

Re: French Cleat Question...

Derek Arita

Thanks for all the help. I thought that the cleat had to be built into the cabinet back to work, but you all have set me straight. We're just about thru painting, so the cabinet will be going up soon. The cleat will make it so much easier to install the cabinet. Thanks again.