Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Stanley No. 6 dimensions

Posts

Stanley No. 6 dimensions

#1

Stanley No. 6 dimensions

Gary Ascher

I have what I believe to be a Stanley No. 6 Type 4.

I am looking for the exact dimensions of the sole. Length and Width.

I see it refered to as an 18" plane. Mine is 17 5/8 long.

The flow chart pfd from WoodCentral points it to a Type 4.

Thank you,

Gary

Re: Stanley No. 6 dimensions

#2

Re: Stanley No. 6 dimensions

Ralph Lipeles

Gary,

I just measured 3 #6's in my collection. One was an exact 18". The other 2 were slightly shorter, 17 15/16" & 17 31/32".

Ralph Lipeles

Re: Stanley No. 6 dimensions

#3

Re: Stanley No. 6 dimensions

Bill Houghton, Sebastopol, CA

Can't help directly, because neither of my No. 6 size planes is a Stanley. But I am going to post a message over on Hand Tools directing folks here.

A little deviation in length won't much matter, of course. More important is how the plane works.

Re: Stanley No. 6 dimensions

#4

Re: Stanley No. 6 dimensions

Gary

Thanks for the reply. I am just making sure it is a stanley. The iron is for sure and all the parts match images I have seen of the Stanley No. 6. The diminsions of mine is 17 5/8 by 2 7/8. I just am trying to confirm everything is a Stanley as I plan on selling most of what I have collected over the years and had stored away.

I am even thinking of selling the Stanley No. 1 plane that I have.

After retiring early this year and bringing home all my tools I used as a wood patternmaker I really do not have room for everything I now have.

Thanks for the reply.

Gary

Re: Stanley No. 6 dimensions

#5

Re: Stanley No. 6 dimensions

Wiley Horne--So. Calif.

Hi Gary,

Came over from the Hand Tools side. My No. 6 is post-WWII, many decades later than yours. For the record, it is 18" long (even) and 3" minus 1/32" wide.

Here are a couple pages from Josh Clark's plane dating website. This page lets you look at features by Type:

http://www.hyperkitten.com/tools/stanley_bench_plane/timeline.php

Down at the bottom, you can pick out a type and look at its features, and compare across types.

For example, if I click on Type 4, I get this page:

http://www.hyperkitten.com/tools/stanley_bench_plane/tl_4.php

Off to the side, it tells you every Type that had that particular feature, which is kinda useful. For example, from Type 4 through Type 15, had a foundry number, "71" or "73" are listed here, stamped into the bed, between frog and knob.

Another clue you can see on this page is that the depth adjustment nut from Type 2 through Type 6 has "Bailey's Patent..." stamped on it. Either of these features should confirm your plane body is a Stanley.

And other plane features can be compared by Type, as well. Caveat: All the type studies are based on No. 4, and absence of a feature is not conclusive, as Stanley was not interested in type studies--just making planes with the parts on hand.

Very best wishes for your retirement!

Wiley

Re: Stanley No. 6 dimensions

#6

I just measured mine, albeit a later type,

Bruce, a MN Galoot

and it is 18" long X 2-15/16" wide.

Re: Stanley No. 6 dimensions

#7

Re: have a look..

david weaver

.. at the ends to see if it looks like someone ground a little off of one end or the other. IF so, and if the grinder of the plane did a nice job a long time ago, it might be difficult to tell.

There are a lot of planes that are a little shorter than they should be because someone chipped a corner of a casting.

Re: Stanley No. 6 dimensions

#8

Re: have a look..

Gary Ascher

The ends have not been ground on and they are as cast.

It is possible that the Type 4 was made shorter. I would love to hear from someone that has a known Type 4.

I am sure they would have made new patterns for all of the Type changes and they could have adjusted the pattern lengths so the casting would come out much closer to 18".

I could see a variance of 1/16 to and 1/8 in a casting that long based on metal temperature when poured and consistency of the modeling process along with many other little problems. But 3/8 shorter like mine is much more that I would expect.

Thank you,

Gary

Re: Stanley No. 6 dimensions

#9

Re: Stanley No. 6 dimensions

Kem

Gary, my Stanley #6 type 4 measures 2 13/16" wide by (just a tad under) 17 11/16" long.

Re: Stanley No. 6 dimensions

#10

Re: Stanley No. 6 dimensions

Gary

Hi Kem,

Thank you those dimensions matches mine precisely.

Now to research the Stanley No. 7

Thanks again,

Gary