Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Looking for box joint jig plans-simple sled

Posts

Looking for box joint jig plans-simple sled

#1

Looking for box joint jig plans-simple sled

Galen Vetterick

I have looked on line for a simple plan for a box joint jig sled for my table saw. There are ones with wood gears and some with threaded rod. Way to complicated. Searching here it seems some older posts the pictures do not show for me. Don't want a miter gauge mounted. I'd like to be able to fine tune the original setup to get the spacing right. I'd like to cut trials till I get a good fit for glueup and then hold that setting.

Can anyone direct me to a good box joint jig plan?

Thanks if you can post a suggestion.

Re: Looking for box joint jig plans-simple sled

#2

Re: Looking for box joint jig plans-simple sled

Dick Coers

From your description, I would make a standard table saw crosscut sled. Then add a second back fence to carry the locating pin. Make a cut through both fences at the same time with them just clamped together. Glue a pin in that groove in the loose fence, and move it over. Clamp to the sled fence and make a test cut. Tap it back and forth to get the right fit, then screw them together. Want to make it a little fancier? Add a t-track to the loose fence, and then have t-bolts to hold the two pieces together.

Re: Looking for box joint jig plans-simple sled

#3

Re: Looking for box joint jig plans-simple sled

Alan in Little Washington (NC)

When you get too frustrated with the DIY jig, go get an I-BOX! :D

Re: Looking for box joint jig plans-simple sled

#4

Got to agree

Henry Higginbotham

Galen, if you're the type that went for those "Build Your Own Bandsaw From Plywood" articles in the woodworking magazines of 30 years ago, then by all means build a box-joint jig. I built one ten years ago or so and cut some good box joints with it once I got it adjusted properly. There wasn't much of an alternative. I used an overlaid sliding face to adjust fit and t-track for the runners. I'll be glad to send you some pictures if you want.

On the other hand, if you want a box-joint jig to help you build other stuff, take a look at the I-Box (IBOX, I-BOX . . . Incra doesn't seem to know). It works as claimed and, as precision tools go, isn't all that expensive.

For a shop-built jig to work really well without the need to recalibrate each time you use it, I think you'd have to find a decent contractor's saw, set it up with a dado, and then never change the dado width or use the saw for any other purpose.

Re: Looking for box joint jig plans-simple sled

#5

Bob

Re: Got to agree

Bob

Spend a little time, some T-Track and some all-thread for the "0" adjuster and your imagination is the only limitation. In the end the results are the same.

Re: Looking for box joint jig plans-simple sled

#6

Not saying you couldn't

Henry Higginbotham

But Galen specifically said he didn't want to. My point was that, to get something even similar to the I-Box, someone with only a typical woodshop at his disposal would spend many hours building a tool that wouldn't improve on the off-the-shelf product's performance (except possibly by a more convenient clamping method), and likely would fall noticeably short.

And if you've truly had an epiphany regarding jig design, or if you just enjoy building gizmos more than furniture or whatnot, then, as I said, go for it. Certainly nothing wrong with that.

Re: Looking for box joint jig plans-simple sled

#7

Re: Looking for box joint jig plans-simple sled

Galen Vetterick

Thanks all for your comments.

My 35 year old table saw is not really worthy of a $170 Incra I-Box, but I do see it could adjust for my somewhat worn miter slot. I just am not sure how often I will use this jig till I at least have something to try on a few projects. Good pieces of plywood and hardware are $0 cost to start with. I never got over the make due mind set since my dad passed away when I was 9 and I had to keep everything fixed or repaired with no money to buy anything new . Must be why I also still have the same old table saw as my family and there needs came first as I grew old.

Re: Looking for box joint jig plans-simple sled

#8

There are lots of table saws on this site

Bruce, a MN Galoot

older than yours. I was with my dad when he bought his (now mine) in the summer of 1964. I understand perfectly the ethos of make it yourself or get by without it.

I made a box joint jig very similar to the versions discussed here, one even for use on my router table (which I also built). They work well enough, are simple to use, but a bear to get exactly right. If you are working with relatively narrow sides, that's not a problem. But if the pieces you are joining are more than 4 - 5", it can be an absolute nightmare to adjust perfectly. That's why the suggestions for an I-Box. I'm giving strong consideration to one of those, too. Of course, it all begs the question of why not just get better at cutting dovetails by hand.

Re: Looking for box joint jig plans-simple sled

#9

Re: Looking for box joint jig plans-simple sled

Alan in Little Washington (NC)

Galen, I honestly understand where you are coming from. I too often feel the same way about tools and jigs. But my experiences with a variety of DIY box joint jigs are what led me to design the I-BOX.

As to your table saw- I was relegated to using a little, lightweight, woefully underpowered, benchtop saw during my I-BOX demonstrations at the recent Klingspor Woodworking show. Other than having to crank down on the INCRA GlideLOCK miter adjusters because this saw's 3/4" (?????) miter slots were way wider than those on my Unisaw, I had no trouble making perfect joints with the I-BOX. The only limitation is that this saw could only handle a 1/2" wide dado blade.

Re: Looking for box joint jig plans-simple sled

#10

Re: Looking for box joint jig plans-simple sled

Galen Vetterick

Thanks all for your comments.

Well after some postings began to make me feel cheap I placed an order for the INCRA I-Box jig. It's all your fault! :D

I guess since there is nobody else in my house to make me feel even more guilty by doing so I will consider this my birthday present, as I turn 65 on Turkey day. I can even cover part of it by an early Christmas gift to myself.

Besides I used up my good plywood that I intended to use for a jig on two other projects.