Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Bandsaw blade tensioner

Posts

Bandsaw blade tensioner

#1

Bandsaw blade tensioner

alan

I have a 14" Delta bandsaw and am close to cross threading my second tensioner rod in the last 10 years. Am thinking about getting a Carter quick release bandsaw blade tension toggle, should reduce the potential for cross threading plus be a quicker approach to tensioning. Anyone have experience and opinions on this or other quick tensioners?

Thanks

Alan

Re: Bandsaw blade tensioner

#2

Re: Bandsaw blade tensioner

Alan in Little Washington (NC)

I can't speak to the Carter, but a few years ago I replaced the standard rig on my Delta that did not have a release lever with OEM lever parts for the newer model. Parts included a new cast iron upper frame, cam lever and a few other small parts. I haven't checked the prices for the parts recently, but the parts for my OEM quick release tensioner cost about half what the Carter cost.

Re: Bandsaw blade tensioner

#3

Re: Bandsaw blade tensioner

Bill Houghton, Sebastopol, CA

I have the Carter; I like it. Quick install, good directions. Mine's on a Jet bandsaw, but I believe the installation is the same on the Delta.

Re: Bandsaw blade tensioner

#4

Re: Bandsaw blade tensioner

Jim Dillon

Alan,

I have the Carter on my 14-inch Delta bandsaw (with riser) and like it. A bit pricey though. Would I buy it again? Yes.

Jim

Re: Bandsaw blade tensioner

#5

Question

John in NM

Why is the tensioning mechanism wearing out? No reason it should really.

Re: Bandsaw blade tensioner

#6

My delta 18 yrs Still good, use every day

del schisler

i clean and oil all the time and it hasn't so far gave me any bad time.

The original and still good, I loosen it every time and i use it most every day for resawing ect. I would say if you never oil it that could help it go bad??

Re: Bandsaw blade tensioner

#7

Re: Bandsaw blade tensioner

Jason Waters

How can the cost be so cheap including the upper casting?

Re: Bandsaw blade tensioner

#8

Re: Bandsaw blade tensioner

Jason Waters

I made one out of threaded rod, and a handwheel and spinner from Harbor Freight.

Re: Bandsaw blade tensioner

#9

Re: Bandsaw blade tensioner

Alan in Little Washington (NC)

A Canadian woodworker contacted the Delta factory to verify the new upper casting and parts would fit his older saw (they did!). I have no idea what the parts cost today but as you can see from the receipt he sent me it cost him $89 CDN for the parts and with shipping and tax the total was only $103 in 2004. I am certain I paid less in US $ for the parts and likely less in tax and shipping to Virginia, but I can't find my receipt. (if my math and web search are correct, $89 CDN equaled $67 USD in March 2004). I have a Delta model 28-254, 14" (Platinum Edition) purchased in Oct 2000. I think the upper casting for the 14" hasn't changed much over time. It is worth checking out.

Here is a photo of and receipt for the six parts needed:



Re: Bandsaw blade tensioner

#10

Re: My delta 18 yrs Still good, use every day

alan

I haven't been oiling it, so maybe that is the problem. I don't know why this happens, but after around 7 or 8 years of use it starts to get more difficult to crank and ends up cross threaded. It's still usable at the moment, but getting worse. I like the idea of the quick release anyway so will probably go that route. Thanks for all the replies

Re: Bandsaw blade tensioner

#11

Re: My delta 18 yrs Still good, use every day

Bayward

My Powermatic 14" bandsaw came from Powermatic with a Carter quick release. I would not have gone out and bought one because of the price but I sure do like it being on my saw.

Do not ask how many times I have started sawing without lifting the Carter arm and putting tension on the blade. Geez, the Carter handle is right in my face when I stand in front of the saw.

Bob

Re: Bandsaw blade tensioner

#12

Re: Bandsaw blade tensioner

Brian

I am mostly impressed that he could find a receipt from 2004. I'm glad to find my saw in the shop!! I bet his shop is clean too.

Brian