Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

use mineral spirits to find glue squeezout?

Posts

use mineral spirits to find glue squeezout?

#1

use mineral spirits to find glue squeezout?

phileas

Hi all,

I built some bookcases out of birch plywood, and made what I'm sure is a common mistake. I used too much glue on some of the joints and ended up with a row of pinhead-size beads several inches in length along several of the joints. I wiped up the excess glue when it was liquid using several paper towels to avoid as much as possible spreading the excess (it's not as bad as it sounds, I hope ). However, I'm sure some of the excess glue remained in place and has now dried.

I seem to recall someone suggesting applying a small amount of mineral spirits to identify where the excess glue had penetrated the plywood, but a quick search of the message boards yielded no results. In any event, my plan is to use the mineral spirits to find the excess glue, and then sand ever-so-carefully to minimize the irregularity to my finish.

Recognizing I'm not going to achieve perfection (and really, who amongst us does?), do I have a sound plan for minimizing the visual consequences of my mistake? What improvement(s) would you offer?

Thanks,

phileas

Re: use mineral spirits to find glue squeezout?

#2

Re: use mineral spirits to find glue squeezout? *LINK*

Larry Barrett

Pete Galbert described using a UV flashlight to find excess hide glue. Getting rid of the excess is a different matter, but this might help you find it.


http://www.chairnotes.blogspot.com/search/label/Glue

Re: use mineral spirits to find glue squeezout?

#3

Re: use mineral spirits to find glue squeezout?

Howard Acheson

Dampen a rag or paper towel with mineral spirits. Wipe the wood and the glue blobs and finger marks will be readily visible. Let the mineral spirits fully evaporate before attempting to sand or scrape off the glue residue. You can also use alcohol which will evaporate faster so you can get back to work faster.

Re: use mineral spirits to find glue squeezout?

#4

JL

Re: use mineral spirits to find glue squeezout?

JL

Works quite well. If you don't want to use mineral spirits, water, denatured alcohol and just about anything that can "wet" out a surface will work. I usually use isopropyl alcohol as it is somewhat inexpensive and slow to evaporate. I typically use the "high test" stuff (90%).

Re: use mineral spirits to find glue squeezout?

#5

some suggestions

Bill Tindall

Suggestions:

I don't know where the commonly advised wiping of glue squeeze-out came from but I think it is bad advice. It turns an inconvenience into a problem by spreading the glue around over a much larger surface. Better to let those beads begin to dry and when they become rubbery pop them off with a scraper or chisel.

If you know how to sharpen and use a scraper it will be vastly faster for removing the dried and smeared glue.

If you are not staining, is the glue a problem? Before I went to much trouble trying to remove a thin film of glue I would test some finish on a glue spot on some test piece of wood and see if it is a problem. It will be a problem if you are staining. But then birch is a problem if you are staining!

In the future applying glue with a stiff brush, "acid" brushes work well, enables a controlled amount of glue to be applied which avoids excess squeezing out. I pour some glue in a disposable cup and apply it with the brush.

Re: use mineral spirits to find glue squeezout?

#6

Re: use mineral spirits to find glue squeezout?

phileas

Thanks everybody. I'm very happy to know that denatured alcohol will also work, and I especially appreciate the tip to be sure all the liquid has completely evaporated; I'm sure I would have rushed and been less than thrilled!

Thanks also to Bill for letting me know when to use the chisel to remove the beads (when they are rubbery). For some reason, that detail has eluded me.

Cheers,

phileas

Re: use mineral spirits to find glue squeezout?

#7

Another tip

John in NM

If you really want it to be easy, pre-sand your parts and give the visible surfaces a coat of tung oil or something similar. Glue just pops right off the oiled surface, especially if the oil is a little wet still when assembly is done. Just have to be careful not to get oil on the joints of course :D

Re: use mineral spirits to find glue squeezout?

#8

Bob

Re: Another tip

Bob

John, I allways prefinish my projects and tape the joints with blue painters tape.