Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Raised shop floor

Posts

Raised shop floor

#1

Raised shop floor

Tom Dunlap

There is a barn at the place that I'm renting that will become my workshop. The floor is poured concrete but shovels were used to smooth the surface not floats...really bumpy. Worse than that the 16x24 main part has one half that's about 3" taller than the other. Then, the other 16x24 part steps down another 3" or so.

My landlord has a lot of 39x41" x 7/8" plywood squares. i don't know how many plys. Nice solid stuff! It would make a really nice floor.

I have access to as many hemlock sawlogs as I want. they have no commercial value so the wood is free, all I pay for is the milling.

Here's my plan...

Have the hemlock milled into 2x4s. Lay these on the flats to become, I think they're called sleepers???. Each plywood edge would have half the 2x4 to rest on. the edge of the whole works would be 2x4 on flats too. Shims and blocking would be added to level the whole works. The plywood would be screwed down.

I've considered raising the floor enough to install ducting for dust collecting underneath. there would still be enough headroom. Having it underneath would be soooo nice.

It seems like the best way to layout the 'sleepers' would to follow this sort of plan:

http://www.homedepot.com/webapp/catalog/servlet/ContentView?pn=KH_FL_Laying_Tiles

I used the Sagulator to get some sort of idea of how much load/flex to expect. It seems like the 7/8" ply shouldn't need support in the middle.

Since I have so much wood I'm also thinking of having 1x6-8 boards made...maybe 5/8 or 3/4...and nailing them up to panel the inside. Let them shrink in place and not worry about the cracks. I might put off the paneling if I can calculate the drying rate over the winter here in Asheville. There is plenty of room to sticker and air dry. It might be worth stalling out the paneling if the shrinkage is too much.

Are there any suggestions or considerations that I'm missing? This is rental property so I don't want to put a lot of time or money into it in case I move out. My landlord said that he might cover costs...wait and see how much the milling costs.

Thanks,

Tom

Re: Raised shop floor

#2

Re: Raised shop floor

Dale warder

A raised floor is so nice! More comfortable to stand on. I have done approximately what you propose, however I used 2 X 6 sleepers, spaced 16" on center. I did run dust collection under floor. The only problem I have encountered is some minor sagging under heavy machines. I replaced a contractors saw with a cabinet saw and had to reinforce the floor under the saw. I also replaced a 14" bandsaw with a 18" cast iron saw and also had to reinforce the floor under this saw. Overall this floor is one of the best features of the shop. After standing on concrete for many years, the wood floor is a pleasure.

Dale

Re: Raised shop floor

#3

Bob

Re: Raised shop floor

Bob

The only other suggestion I have, if your just did not mention it or someone else has already suggested it in which case sorry for the extra space. I would lay 15 Lb. felt over lapped by half this will help keep ground moisture from causing any sort of problem. If there is a moisture problem at all I would lay some sort of poly sheet type barrier over that.

Re: Raised shop floor

#4

JL

Re: Raised shop floor

JL

I would go the 2 x 6 route (or 2 x 8). I would also have 2 layers of plywood - even though you think it won't sag.

My friend Mike's shop has 2 x 12 floor joist. He's got 2 layers of Advantek floor plywood (3/4) laid so they are staggered. No sag with 15" planer, cabinet saw or any other tool.

Re: Raised shop floor

#5

Re: Raised shop floor

mdclor

I know that it's a rental and it might not be necessary in NC, but if it isn't too expensive you might enjoy having some insulation between the concrete and the plywood. Just a thought.....

Re: Raised shop floor

#6

Comments

Tom Dunlap

-I thought of the vapor barrier but I didn't mention that in my original post. More than likely 10 mil plastic on the floor.

-After running numbers through the Sagulator calculator I'm confident that my design is good enough. My planer is a 12" Ryobi lunchbox and I have a 12" Rockwell contractors table saw. The heavies are the four drawer file cabinets full of small power tools and supplies. along with my multi-drawer mechanics toolchests. These will be along outside walls. If the floor does feel spongy it would be easy enough to add another layer of full sheets of plywood over the top.

-Insulating the floor crossed my mind. If it were my shop I'd consider it. Since this is rental I'm not spending the money. Besides, I lived in Minneapolis until I was 50 and only had concrete floors in the garage. Down here a wood floor will feel comfy.

Thanks for the comments,

Tom

Re: Raised shop floor

#7

Re: Raised shop floor

Larry Clinton At Frankfort, (Central) Indiana

Tom, sounds like you have it planned out pretty well.... Suggestion, instead of waiting to panel, you may want to do the walls in board and batten - with plastic under for a wind / vapor barrier. The board and batten would allow shrinkage while on the wall without any problem. A few years ago I watched a gentleman panel the outside of a fairly large building with green lumber using board and batten - then he sprayed the entire building with an oil preservative - looked pretty good - he said he had done it a few years ago with no problem.

Re: Raised shop floor

#8

Re: Raised shop floor

Tom Dunlap

A vapor/wind barrier on the walls would be super easy to install.

If the wall boards go up green I might wait to see how much shrinkage there is and then put up battens. The boards will be horizontal. I read a tip about B/B that suggested only nailing the board in the middle to allow both edges to move while they dried. Putting in two nails per board might cause some funky crooking.

Tom

Re: Raised shop floor

#9

I'd go with felt rather than plastic sheet...

John in NM

Felt is much more durable on a rough surface, and the asphalt will basically last indefinitely since there is no UV exposure. The purpose is a moisture barrier rather than a vapor barrier - you're trying to keep moisture from the soil from wicking through the slab and wetting your sleepers.

If this were a living space, you would likely need to apply a vapor barrier to the floor above the sleepers and vent the space in between, or dispense with the wall vapor barrier and allow the structure to breath. But a shop space is not likely to have a large moisture differential between the inside and outside air - unless you plan to cook and shower in the shop :D

Re: Raised shop floor

#10

Re: I'd go with felt rather than plastic sheet...

Tom Dunlap

Good point about on the cement floor. Tar paper it is.

On the walls plastic will be much easier to install and work with. The outside barn walls are pretty leaky. Keeping the blowing wind out will make it a bit more comfy.

Most of the work will be done solo. Moving rolls of roofing felt is hard enough on the roof, I don't even want to think about shlepping them around vertically.