Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Compressor for spraying lacquer or poly

Posts

Compressor for spraying lacquer or poly

#1

Compressor for spraying lacquer or poly

Jerrid Edgington

What size of compressor do I need in order to spray poly or lacquer ? I have a hobby of refinishing wood furniture and I want to start spraying rather than brushing. Any helpful tips would be greatly appreciated.

Jerrid

Re: Compressor for spraying lacquer or poly

#2

Re: Compressor for spraying lacquer or poly

Ralph Lipeles

Depends oh how big the pieces are that you are spraying. I used to have a sprayer with a 20 gallon tank. I thought it did a good job for me until it went and I replaced it with a 60 gallon unit. The bigger one was quite a bit better. I believe that the difference is because the larger tank holds more air so that the compressor is not turning on and off very often. This keeps the compressed air cooler and that means the air contains less humidity.

Ralph Lipeles

Re: Compressor for spraying lacquer or poly

#3

Jim DeLaney, Austintown, Ohio

Re: Compressor for spraying lacquer or poly

Jim DeLaney, Austintown, Ohio

Instead of a compressor, you might consider one of the smaller HVLP set-ups, like the Earlex. Rocklers, Woodcraft, et al, have them.

Re: Compressor for spraying lacquer or poly

#4

Re: Compressor for spraying lacquer or poly

Larry Clinton At Frankfort, (Central) Indiana

As has been stated the larger tank (and cfm capability) of one of the 60 gal units will give you some advantages such as less moisture, even pressure etc. A couple of issues - both lacquer and polys are pretty easy to spray, but in my case, I have always thinned more than most to achieve the best results. A good regulator and filter system is required as is regular draining of the tank of water to eliminate moisture. I would definitely stay away from any "oil-less" units as their life is much shorter than the oil type units. I personally opted for a 60 gal severe duty (cast iron cylinder) Campbell Hausfield compressor and it has met my needs well for the last 6 years or so. I personally have had experience with Airless and HVLP industrial units in my former occupation as an engineer and have not seen any advantages of these in hobby use.

Re: Compressor for spraying lacquer or poly

#5

First Step

Howard Acheson

Buy the book Spray Finishing by Charron and/or Spray Finishing Made Simple by Jeff Jewitt. Amazon will have them. They will give you all the info you need about compressors, air sources and guns. They will also tell you how to set up and adjust your equipment as well as how to "read the spray" to know what needs to be adjusted to get the best finish. They will tell you the techniques of spraying--you don't just fill up the gun and pull the trigger. A week or two practicing on cardboard boxes and/or wood scrap is required. Never start out on a real project.

You mention spraying oil based finishes but these are problematic. Oil based finishes are very slow drying and the overspray is in the form of liquid droplets. They will float in the air and get on everything in shop or area leaving a crust when it dries. Oil based finishes should only be sprayed if you have an efficient spray booth or you spray outdoors. It's best to spray only fast drying finsihes like lacquer, shellac or waterborne finishes.

Re: Compressor for spraying lacquer or poly

#6

Re: First Step

gary peterson

question...I am not familiar to spraying as I've been wary of overspray as mentioned. Would the laquer or wb have overspray also, you know float around the room getting on everything? I have always assumed a spray booth was necessary for spraying finishes. My finish is now oil/blo/min oil hand applied, but can change. Thank you for any help. gary

Re: Compressor for spraying lacquer or poly

#7

Re: First Step

del schisler

i spray lacquer for yrs now. I have a 25 gal tank with a out board comp. Not one of those oilless unit's. I have 2 filters on the unit one next to the tank and one next to the spray gun. You spray with 30 lbs of air . And my nozzel is a 2mm . This work's out fine. I have a shop. I spray in frount of the window that has a 30" exhoust fan. Now the apray get on the blade's and window's but i clean them. All the spray goes out side. Now when you spray goes spray from you to the other side. Or start and spray away and that way the spray doesn't go over what you have just sprayed. Of course no over spray. Now when you spray inside of a box with no where for the spray to go you are going to get over spray. Buy with practice you can get a finish that will look good. I use M.L.CAMPBELL lacquer which i can get close by. Shermen william's lacquer is good also. I thin the lacquer around 10 percent with thinner. I also use m.l.campbell thinner only not the box store stuff. Good luck

Re: Compressor for spraying lacquer or poly

#8

Bob

Re: Compressor for spraying lacquer or poly

Bob

For the same price of a compressor you could get an Earlex 5500 here is a review by Top coat they cost about $320. The biggest advantage is that it is a turbine so it supplies a constant the air you need but most of all its drier filtered air which is essential for the finishes you are working with.

http://topcoatreview.com/2011/09/testing-earlex-spraystation-5500-hvlp/

Re: Compressor for spraying lacquer or poly

#9

Re: Compressor for spraying lacquer or poly

Richard McComas

I always though the first step was to look at the spray gun you what and see how many CFM it requires.

Re: Compressor for spraying lacquer or poly

#10

Re: Depends

Larry Clinton At Frankfort, (Central) Indiana

I have several spray guns that range from a CFM at 30 - 60 psi requirement of 3 -5 up to pretty close to 8 CFM. All of the guns I have with the exception of a couple of HF and my air brushes were purchased at Estate sales or Auctions- price range of $2 to $15 - There are a couple of nice Binks and other decent guns in my assortment of about 6-8 guns. If you start with a 60 gal moderate priced ($400 - $600) compressor you can use just about any gun you want. Another advantage of the larger compressor is the fact you can if you wish run power tools, small air sanders and even small sandblasters.

Re: Compressor for spraying lacquer or poly

#11

Re: First Step

gary peterson

thank you for the reply...think I'll do some more thinking. gary

Re: Compressor for spraying lacquer or poly

#12

Re: Compressor for spraying lacquer or poly

Jerrid Edgington

That hvlp system that was posted looks great. Does this work for spraying poly or lacquer ?

Jerrid Edgington

Re: Compressor for spraying lacquer or poly

#13

Bob

Re: Depends

Bob

Moisture could be a problem and not knowing the environment he is in could produce a bad finish using the coverings he is talking about. I would still get a small turbine unit like the one I suggested. A 60 Gal tank is sort of OK if he gets a good 2 stage compressor. I have a 60 Gal I got from Home depot and it don't do the job.

Re: Compressor for spraying lacquer or poly

#14

Re: Depends

Larry Clinton At Frankfort, (Central) Indiana

Don't understand why you have had a problem Bob. My 60 gal unit is a Single stage rated at about 9 Scfm at 90 psi. I live in a pretty humid area here in Central Indiana, and do have to add retarder to my Lacquer occasionally to prevent blush, but have never had a problem I couldn't handle. I do my spraying outside, and do avoid extremely humid days (usually to hot and humid for me anyway). I use Behlen Qualalacq lacquer - conventional nitrocellulose - and usually Minwax Poly, both thinned considerably as I stated. Never had any issue with the Poly at all.

Re: Compressor for spraying lacquer or poly

#15

Bob

Re: Depends

Bob

I am in the south and even after cleaning my guns and not using them for a few months I have had the gun rust. Forget about using Latex at all.

Re: Compressor for spraying lacquer or poly

#16

Bob

Re: Depends

Bob

Larry let me restate where I lived I am now in Mid Atlantic area but was in Florida.