Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

recharging ni-cad batteries

Posts

recharging ni-cad batteries

#1

recharging ni-cad batteries

Joseph Mulherin, sr

Just went to YouTube and watched a couple videos on how to recharge your battery drills....very simple....use other batteries to get the higher voltage and amperage or use your welder...very interesting.

Just go to the YouTube website and type in battery recharging and up will come many videos to view.

Hope this helps you....batteries are very expensive to just replace....why not recharge using these videos.

Also, there is a video showing how to convert an old battery drill do a corded one.

Good Luck....Joe

Re: recharging ni-cad batteries

#2

Re: recharging ni-cad batteries

Bill Howatt

You can try it and if it works you win at least for a while but often it doesn't fix the problem. Nothing to lose unless something goes terribly wrong with the welder trick. :D

Bill

Re: recharging ni-cad batteries

#3

Re: recharging ni-cad batteries

Bill Tindall

You Tube is not the place I normally look to for information on the complex task of charging a battery as complex as those to be found in cordless products. But who knows? Maybe someone with a welder has discovered something that has escaped discovery by the people that design and build these things. Lets us know how it turns out. If the safety features built into the battery fail the results could be spectacular.

Re: recharging ni-cad batteries

#4

Re: recharging ni-cad batteries

Mark Nowicki

Did a quick search on eBay. Makita replacement battery $65, Miller welder $1600.00.

Mark

Re: recharging ni-cad batteries

#5

IT does work

del schisler

i have been doing this for yrs. When you speak of a welder people thank of a big voltage thing?? It could be but you only need we will say 24 volt's will work. this is what i use. Any voltage larger than the battery. 12volt i use 24 volt and it will work. just make sure pos to pos and neg to neg. What i do is hook up a clip to the neg. than a clip to the pos . Now just ark it to the pos DON'T hook it up and like try to charge it. Just flash it . I do that 6 or so time's work's for me. Now the battery will charge it but will not be as good as new but will work a little longer. Sone of the charger's i belive won't charge if the battery is under 3 volt's so a flash will give it enough for the battery to charge. I have done this and it work's for me. Don't knock it tell you have tried it? Just be a little carfull and all will work out ok. my 2 cent's

Re: recharging ni-cad batteries

#6

Re: recharging ni-cad batteries

Joseph Mulherin, sr

OK, messages have been posted....BUT...did any of you ever go to the YouTube and watch the videos....or are you just making some comment based on your present knowledge. I try to post things I find which will help others. The welder is NOT being used to WELD but just used to tic-tic-tic about 5 times on the minus side of the battery to stimulate, then it is placed into its recharging unit to fully recharge again. And a small mig welder is used without the wire activating. Watch the videos before making some comments on something which you have no knowledge of. Rant over...

Re: recharging ni-cad batteries

#7

Re: IT does work

Joseph Mulherin, sr

Thank you, Del, like I just said on my rant...go watch the videos before making some comments.

Re: recharging ni-cad batteries

#8

Re: recharging ni-cad batteries

Bill Howatt

No need to rant.

I have done it and it did work but for a very short time on 2 batteries and not at all on a third. What the welder is doing is blowing out the sulfonation spikes or whatever to remove an internal short or high-leakage. However, I did mine with a battery charger not my Miller Thunderbolt stick welder that puts out 80V AC, not DC, OC.

So I extended the life a bit except the internal discharge rate was still higher and I could not rely on the battery being charged when I went to use it after a few days. It reminds me of the days when money was tighter of friends and myself buying car battery warmers and making trickle chargers to be mounted under the hood to keep a failing car battery going in the winter when the real problem was that the battery had come to the end of its life.

I have also tried the freezer trick and it never worked at all.

Bill

Re: recharging ni-cad batteries

#10

Re: recharging ni-cad batteries

Bill Tindall

This battery type and to a lesser extent the nickel metal hydride battery is particularly picky about how it prefers to be charged. The best battery life will result from charging with a high quality charger which programs an optimum current and voltage delivered to the battery during the charging cycle. Heat is a battery's major enemy, especially when charging, but also in storage and discharge.

Re: recharging ni-cad batteries

#11

Re: recharging ni-cad batteries

del schisler

i have done this . I am using what i have done. Before you post things like have you done this or just reading some post and than saying oh i can do this . oh well got better things to do. my 2 cent's