Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Reclaimed Asian Teak

Posts

Reclaimed Asian Teak

#1

Reclaimed Asian Teak

Bryan Donahue

Hello Everyone,

I'm looking for some advise. I have about 2000BF of rough sawn, reclaimed old growth Asian teak that I'm looking to sell. So, what price per Bf would be reasonable to sell at?? Thanks in adavance for the help.

Re: Reclaimed Asian Teak

#2

Essential data missing......

Bill Tindall

To get to the point I don't know. But no one could know from the information provided. Anyone interested will need to know if it is suitable for their intended use which could range from fine furniture to bridge decking.

More important than species in determining price is the condition and quality of the lumber. Before anyone would buy any lumber they need to know how many defects it has- knots, splits, twist and cup, nails and nail holes, rot, stain or anything else that would render all or some parts of the lumber unsuitable for this or than need. Additional the length, width and thickness needs to be revealed and finally moisture content, and where it is at.

Just to provide one example the wholesale price of walnut at the mill can range from $0.30 to $3.00 depending on lumber's size and the amount of defects the lumber has. The range for teak would be even greater.

Re: Reclaimed Asian Teak

#3

Re: Reclaimed Asian Teak

Mark Valsi

I'll give you $.50 per b/f for 100 bf !

Re: Reclaimed Asian Teak

#4

That's reasonable for Mark not Bryan,

Dick Coers

but he did say reasonable!

Re: Reclaimed Asian Teak

#5

Re: Reclaimed Asian Teak

John in NM

Bill made some excellent points, to which I will add a couple.

Do you plan to sell the whole lot, or multiple large lots to just a few customers? If so, you'll need to reduce the price to more of a "wholesale" level. If you are willing to sell a board or two at a time, you'll be able to get a higher price.

If your estimate of the grade is FAS, you may have good luck selling to someone who does work on boats/yachts - teak is often used there, and if its good lumber you may find a buyer for large lots.

Be prepared to explain the rather odd combination of reclaimed and rough sawn - a bit unusual to find premium woods such as teak used in a rough state. Its not like anyone built a teak barn.

Last time I priced any, it was (retail) $30-$40 per board foot for 4/4 FAS, depending on source and dressing, that was easily 5 years ago though. Someone buying 2k bdft would probably expect a considerable discount on such a price.

Re: Reclaimed Asian Teak

#6

JL

Re: Reclaimed Asian Teak

JL

Need to know thickness, width, length and general condition.

Teak isn't inexpensive - but you still have to know what you are buying.

As an example, 4/4 red oak is $2.35 a board ft for FAS. If I'm buying it at 10" W or better, it can run $2.95.

Re: Reclaimed Asian Teak

#7

Re: Reclaimed Asian Teak

paul in AZ

I don't know what current prices are but a lot will depend on what you mean by "old growth". As a former sailor with exposure to wooden boats I can tell you that almost all of the teak on the market for many years now is garbage.

Really good teak is uncommon and even more expensive.

Finding a furniture maker who wants to buy it to compete with asia will be a low yield game.

Try yacht builders and I don't mean those that build plastic boats we called 'chlorox bottles'. Perhaps go to some of the wooden boat websites or pick up a copy of Wooden Boat or one of the other magazines like it.

Re: Reclaimed Asian Teak

#8

Re: Reclaimed Asian Teak

Bryan Donahue

Thank you all for the responses!

This allows me to give details. The wood is definitely old growth Asian teak (I had it tested, and they said it was from Burma). The wood was used to build (by master Chinese artisians flown in from China) a $100 million dollar facility here in Florida, but it unfortunately went belly-up. The teak is of door and window frames that were 4/4's. The sizes (generally 2 to 3 boards for each frame) that I'm able to net out of the wood are mainly 3' to 10' L / 1" to 4" W / and 1" to 2.5" thick. I have extracted only about 1/8th of it so far, and de-nailed, de-screwed (if that's a word), cleaned, and cut it on a table saw. The wood is beautiful. I asked the initial question because I'm trying to decide if I should/can sell it in one or more large lots, or if I should try my hand at retail. I'm leaning towards selling it in large volume without me even table sawing it. The reason for this (in my mind) is so the potential buyer can make the cuts he/she wants, and because I don't have the marketability as someone that's been selling teak for a long time. I've had an informal offer of $8 a bf.....is this a good offer?

Thanks again for the advice!

Bryan

Re: Reclaimed Asian Teak

#9

Re: Reclaimed Asian Teak

paul in AZ

I just looked up a local lumber yard and their teak price is $39.95/BF.

BUT... and this is a huge BUT... that is not for shorts, for boards 5 to 7" wide, with no nail holes.

If it were mine I'd lean towards negotiating a bit with that soft offer and taking what I could get. Narrow little boards like yours with nail holes likely have a limited appeal unless one is making picture frames.

Re: Reclaimed Asian Teak

#10

Bob

Re: Reclaimed Asian Teak

Bob

I have sold reclaimed Teak as well as Cinker Cypress in Florida, New Port Richey in fact to restoration contractors that did work in Tampa and St. Pete, I sold it for $7.00 per bft Wholesale. If it was under 100BFT and I had to sort and clean it I sold it for $11.00 bft, there is quit a bit out there if you look. I had a small one man operation up until I moved to VA. prices are crazy here. Don't price yourself out of the market. Stay away from craigslist all I got were scammers.

Re: Reclaimed Asian Teak

#11

Ellis Walentine

Some thoughts

Ellis Walentine

First, you mentioned nail and screw holes. I don't know how many of these there are, or how they affect the appearance of the wood, but that might be a factor in the value. Also, if some of the wood is in narrow strips, you might want to list the various dimensions and sell it by the running foot.

Since you have so much of it, you might be interested in listing it as a "Hot Deal of the Moment" on our other site, Woodfinder®. This service is not free -- we charge a sales commission for the service, but it will be seen by many thousands of potential buyers in a short time. Let me know if you're interested and I'll explain how the listing works.

You could also place a classified ad in Wooden Boat magazine. I imagine their readership is the likeliest prospect for this wood, and they are accustomed to paying high prices for everything associated with boats. If you are going to have to sell it in retail quantities (and 10-footers won't go UPS in any case), you will have a lot of extra work invested in selecting, packing and shipping the stuff, so factor that into your pricing.

Old-growth Burmese teak is beautiful wood. It has a rich, dark color and finer growth rings than the bland plantation teak that dominates the teak market these days. Burmese teak has been grown on plantations in Burma since the mid 1800s and protected carefully by the Burmese government over the years, so quantities have been limited and prices generally high.

Ellis Walentine, Host