Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Marking my work

Posts

Marking my work

#1

Marking my work

mdclor

There was a thread a few days ago about marking one's work. This is something that I would like to start doing, but I have some questions. I am selling end grain cutting boards, like about a million other people. :/ I would ask anyone that has experience to weigh in on the pros and cons of using a branding iron versus gluing a "coin" into a drilled hole.

I see the coin as having the potential to fall out even if the hole is perfectly sized and epoxy is used. Is this a valid concern? On the flip side, I think the coins are a better looking mark.

The brand would require some experimentation to get it just right, i.e. neither too dark or too light. Also, it would not show up well on walnut or any other darker wood. However, the brand is much more cost effective. Is the electric branding iron worth the price premium over the torch heated iron?

What is the verdict of the collective WC brain trust?

TIA,

Merle

Re: Marking my work

#2

Re: Marking my work

steve mackay

Inseting anything like the "coin thing" is classy ! I always thought the "branding" was rather crude-ish.

Re: Marking my work

#3

Re: Marking my work

Carol

If I felt the need to do this, I'd design an informative 'brand' and have it lasered out of thin Baltic Birch plywood. It is blond and wood. Drill a shallow mortise and glue in before the final finish. You could combine graphics with words and be very distinctive. Informative being with your logo and contact information. Leave room for a number which you can hand write in upon installation.

Re: Marking my work

#4

Baltic birch will fall apart when wet. *LINK*

Keith Newton

However, it could be done on a single thin re-sawn piece of wood which could be glued on.

As for the coin idea, epoxy would be a bad idea if glued onto the end grain, but should be fine if used on the side, due to the greater potential for movement on the end-grain, and epoxy being too brittle to move.

I just use a cheap burning tool, with a skew tip to sign my work. At the time started doing it this way, I was into a oriental phase of designing, so I wanted the lettering to look right. But then, it became my logo.

Curved lines like O e or C are harder than straighter lines, so it takes a little practice to get the hang of it. Giving it a cuneiform look seems to work for me.

It normally takes about 10 ~ 15 minutes to sign and date my work.


http://www.flickr.com/photos/7391658@N03/sets/72157630774703276/

Re: Marking my work

#5

David Barnett

That's terrific looking, Keith

David Barnett

First truly classy pyrographic signature I've ever seen.

Re: Marking my work

#6

! . . .

steve mackay

I've seen the modern cards like that. VERY cool ! I wonder how time consuming it would be to do a marqueterie kind of thing on pieces ? Now that WOULD be classy.

And haven't I seen something similar from Ye Olden Days (like middleages) ) that were used as "secret" message cards or calling cards ? They were broken in half then authenticated by matching the grains of an individual card. Antiques Roadshow or something like that.

Re: Marking my work

#7

What I used to do...

John in NM

Was print an old looking label on some nice paper and laser print it. Stick on with some hide or fish glue behind a drawer or something. The shop I used to work for did that, but they are also seen in a lot of antiques. When and if I end up making more furniture I'll stick with this marking.

Neither branding irons or coins are for me, but maybe in 100 years the coin idea will be like the paper label.

Re: Marking my work

#8

Re: Marking my work

mdclor

Thanks for the suggestions. I am not artistic like Keith, so I may put pyrography on the back burner. I like Carol's laser engraving idea, but on solid wood as suggested. What ever I do, I would prefer to put it the side of the boards for the better glue adhesion and to avoid movement issues. Any more options?

Re: Marking my work

#9

Re: Marking my work

Carol

Merle, contact Nancy Laird in Rio Rancho. She and Dave do laser work. She did some work for me on BB and there are/were no delamination problems. Sounds like a bit of hooey gleaned from no first hand experience. Though they will use solid wood it you like. If you need contact info, let me know. She and Dave were at that get together we did a number of years ago at your shop.

Re: Marking my work

#10

Hooey?

Keith Newton

You may be able to find exterior or even marine grade BB in some locations, but not where I live, or at least not back when I chose to use it for some pierced details on a restoration job about 30 years ago up on a little gable with plenty of overhang to keep direct rain off.

It fell apart in less than one year. That was embarrassing, for me to have shown such poor judgement. I have used hundreds of sheets since then for interior purposes, and seen plenty of scraps delaminate from getting rained on out in the dumpster. Your milage may differ, but if it doesn't say exterior, it probably isn't.

MD probably generates plenty of scrap making those cutting boards, which ought to make a great substrate for your laser suggestion.

Re: Marking my work

#11

Re: Marking my work

pecker

If you can come up with a simple design which you could engrave with a dremel tool, there is a product called INLACE which you mix up and pour to fill the engraved area. Then just sand flush.


img

Re: Marking my work

#12

Re: Marking my work

mdclor

Thanks, Carol, I left a message for Nancy this AM. :)

Re: Marking my work

#13

Re: Marking my work

mdclor

Pecker, that is an attractive board. I have seen the InLace product before, but had forgotten about it. I will have to research this a little to see it it might work for me.