Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Frame and panel joinery

Posts

Frame and panel joinery

#1

Frame and panel joinery

Bill Tindall


The side of the chest of drawers will be a frame and panel and I have a nice board for the panel. For a typical frame I use the joinery illustrated in the following two pictures.




This simple cope joint is strong and the coped molding part makes a nice joint. However, the profile on the frame for the chest of drawers is a bit complex for the cope so I chose to just do a miter. The miter is pared with a guide block and chisel.


This picture shows the assembled joint.


Re: Frame and panel joinery

#2

Re: Frame and panel joinery

William Duffield

That's the way I've usually done them too. I use your trick of raising the table saw blade up all the way to trim the bead off the ends of the stiles, figuring the end of the kerf won't be noticed on the inside of the door frame. Lots of shellac does a good job of disguising the mitered quarter round. When I was doing a lot of them for a large kitchen, instead of the f-clamp, I found it handy to screw a toggle clamp to the miter guide block.

Re: Frame and panel joinery

#3

Ellis Walentine

Mason's miter

Ellis Walentine

I've used this joint a lot but I've always heard it referred to as a mason's miter. In a coped joint, the end of the rail is coped to receive the bead on the stile.

Nice tutorial. Thanks.

Ellis

Re: Frame and panel joinery

#4

Re: Frame and panel joinery

TomD

Those are some really clean looking parts, though I have to say the resulting assembled joints have surprisingly coarse tolerances. :)

Re: Frame and panel joinery

#5

Re: Frame and panel joinery

Bill Tindall

I need to make the mortises deeper next time! A "little" filler will fix it up ok

Re: Frame and panel joinery

#6

Re: Mason's miter

Sgian Dubh

Ellis, I can't see what I recognise as a mason's mitre in any of the images seen thus far in the thread. I see a scribed moulding, aka coped, and I see a mitred moulding, both at the inner intersecting corners of M&T joints, but not a mason's mitre.

The image below is what I know as a mason's mitre. This example comes from that reliable source, Hayward's Antique or Fake, 1970, page 248. Maybe I'm picking up something wrong in your message? Slainte.

Photobucket

Re: Frame and panel joinery

#7

Re: Frame and panel joinery

Barry Irby

Caulk is your friend

Re: Frame and panel joinery

#8

Re: Frame and panel joinery

Tom Colligan

Bill, how did you make the moulding? Straight through with a moulding plane from end to end of the board after making the groove? And then deal with the coping and mitering afterwards?

And, is that a picture of one of the chisels you made? If so, I may just buy a length of flat stock after all and use a hack saw to cut what needs to be done. TIA, Tom.

Re: Frame and panel joinery

#9

answers

Bill Tindall

groove, edge moulding, coping and mitering afterwards.

And, is that a picture of one of the chisels you made? yes. they are trivial to make. I f people understood how cheap and easy one can make the best chisel money can buy it would be more common to see people making their own chisels and not paying $70 each for good ones.


The sizes up to 1/2" are just a rectangle of 1/8" bar stock. Grind a shoulder for the wider sizes. In the PIC I made the middle and bottom chisel but the "pattern" is common in old chisels like the one on top. they don't needs to be as ugly as the ones I make if you want to refine and polish some.