Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Drill Press

Posts

Drill Press

#1

Drill Press

Lynn Reedy

I am in the process of selecting a new drill press for my shop.

I have several powermatic tools but have not bought anything new

in several years. Powermatic is my first option but I keep hearing bad

stuff about the now day powermatic equipment vs. the old day equipment.

Anybody got any advise on brand or size of drill press. I am not considering

a bench top size.

Thanks

Re: Drill Press

#2

JL

Re: Drill Press

JL

I don't have Powermatic tools - but I do have a number of Jet tools. I have seen and used the more recent Powermatic lathes (3520B). I am happy with my Jet lathe and reasonably happy with my Jet drill press (I don't really like the table that much).

All in all, I think most of the WMH tools are good tools. While I have seen the quality of some of the Delta tools seriously falling in the past 10-15 years, I haven't really seen that with any of the WMH tools. Admittedly, I haven't looked at too many of the Powermatic, just Jet tools.

Re: Drill Press

#3

Re: Drill Press

John in NM

Pretty hard to go wrong with a drill press, not a lot of potential problems other than cheap plastic shrouds breaking or the motor failing after a couple years. I was looking at the General International model, because the big outfit in Albuquerque has them in stock, and they have a long travel, 6" or so.

One thing I look for now is the ability to tilt the table 90 degrees, I've found that really handy on my Rockwell bench model (also has 6" travel).

The other thing I like in modern imports is that many of them have hand cranks for raising the table - not a big deal but makes use a little easier. We have a Jet at work, the crank has been replaced with an aluminum one - original was probably plastic or zinc and broke.

The one thing that Jet doesn't have that I find handy on my old Rockwell is a vertical travel lock. Makes it a lot easier to align your location and then clamp the work - I've had my hand whacked often enough to be really big on clamping the work :D That drives the "safety" guy at work nuts, because he's always bugging me about unimportant stuff, then I lecture him whenever I see him using the DP without clamping down the piece of 1/8 steel he's drilling a hole in :D

Re: Drill Press

#4

I have the Powermatic 2800 *LINK*

Dave Paine

I had been considering the Powermatic 2800 and the Delta Model 18-900L

The Powermatic happened to be on-sale at Woodcraft and so I made the plunge.

The manufacture of the unit was moved to China, sad to say, but the build quality of my unit was good.

Despite the "cons" below, I have been happy with this purchase.

The variable speed design is two sets of cones with a spring arrangement. The lever changes the distance between the cones and hence the speed. So far working well. I thought I would get belt slippage, but so far not observing.

I did not research the Delta. It also has a variable speed. I do not know the design. I was interested in the Delta table design which tilts left / right and up / down. Since I never used it I do not know how rigid the clamp is.

Pro's for the 2800

Excellant chuck. Perhaps the best feature of the machine. Capacity is 1 - 16 mm. So goes from really small to just over 5/8in. Impressive range, but the build quality is even better. This is hand tightened, but I do not have to apply a lot of force.

Good size motor - 1HP. I have not had the motor feel to bog down.

Good depth stop - threaded rod style.

LED light is useful

Lasers are accurate, but sometimes the bit gets in the way.

Variable speed. Works well, easy to adjust so I actually use it.

Heavy castings. You do not want to need to move this once in place.

Large and rigid table with T slots. I use the T slots a lot.

The levers for operating the head can be installed on either right or left side.

Motor is quiet. The variable speed belt can be heard, but not noisy.

LED speed readout. I find this useful, especially to remind me if I install a large bit, but previously was running smaller bit at higher speed.

Con's.

Biggest gripe is the crappy too small screw for the speed adjustment. Large knob but inside it is 1/4in screw.

Second biggest gripe is no power off switch. The LCD speed readout shows "0" all the time. I had to plug the drill press into a power strip so that I could turn off the power for the unit when I am not in the shop.

Fence design. The dust collection got in my way to I replaced with Woodpecker DP3 fence. Much more useful

Table wing extensions held in place by plastic rings. I am afraid I could break these.

Plastic table insert with wide hole. I kept dropping drills through the hole. Finally I turned a piece of walnut to fit and no longer drop the bits through my solid insert. I like having an insert, I just prefer solid.

Rack for height adjustment does not go all the way into the head. Instead they have a collar which does not mount level. Works, but chinsy.


http://www.woodcraft.com/product/2020484/22531/powermatic-2800-18-variable-speed-drill-press.aspx

Re: Drill Press

#5

Re: Drill Press

Jesse Cloud

As usual, John pretty much nailed it.

One other thing I would add, if you are using big forstner bits or hole drilling doohickeys, check the max speed recommendations. Some want to run as slow as 250 rpm and many drill presses don't go that low.

Re: Drill Press

#6

Re: Drill Press

TomD

I like to get old iron in this category.

As far as rpms I think this is a case for variable speed.

Re: Drill Press

#7

Re: Would not recommend Powermatic

Larry Clinton At Frankfort, (Central) Indiana

I have the Powermatic 2800 China made ($1000 press) and would not recommend it to anyone. I have had several of problems with the chuck, - doesn't fit well into the drive shaft, wants to clamp bits off center etc. The unit is very noisy compared to the older presses made in the US. Fit and finish about on a par with Harbor Freight tools. If I had a chance to do it over again I would purchase a Grizzly. I honestly believe Powermatic, Delta etc. are buying cheap China made tools and selling them at a higher price based on their reputation earned from American made tools. I also believe Grizzly has a far better handle on quality control of the Asian made tools, they are usually better made, cheaper and have a better supply of replacement parts and in whole have a better warranty and customer service. I have an older American made Powermatic lathe, Delta Unisaw, Routers etc and they are excellent quality. When I looked at the newer tools at the last show I attended I decided I would not purchase any "Brand names" made in Asia. My 3 hp Cyclone is a Grizzly and although I did have some problems, Grizzly did a great job of correcting those, I also have an 8" Grizzly joiner with the segmented head and it has been perfect. You may also look at the used market as some suggested - I believe a 20 year old US made drill press would be more accurate and last longer than a new Asian made unit.

Re: Drill Press

#8

Re: Would not recommend Powermatic

Lynn Reedy

My thoughts are the same as yours on new powermatic equipment.

What is your opinion on rikon equipment? I have never heard a bad

word about their equipment.

Thanks,

Lynn Reedy

Soddy Daisy Tenn.

Re: Drill Press

#9

Re: Would not recommend Powermatic

Larry Clinton At Frankfort, (Central) Indiana

I really haven't looked at the Rikon machines other than in ads. From all appearances it is an importer that wants to be a Grizzly. Unlike you I have read several complaints about both their machines and their customer service. You might do a little web searching and read customer comments. With the service and quality I have received from Grizzly I would not chance purchasing from Rikon. If at all possible I will always buy American made - sometimes there is no comparative machine built in USA or the price is more than double - then I look at Grizzly.

Re: Drill Press

#10

Very Happy With My Grizzly Drill Press

George Colonel's Workshop-Havertown PA

Good Afternoon Lynn,

I have acquired the Grizzly floor model radial drill press and am pleased as punch with it. For my work it is perfect for my shop needs. No complaints after four years.

George

Re: Drill Press

#11

Are you saying you couldn't bear to part with it?


Re: Drill Press

#12

David Barnett

One could infur it'd be impawsible to replace.


Re: Drill Press

#13

David Barnett

At the local maul, that is.


Re: Drill Press

#14

David Barnett

Would insurance even begin to reimbUrsus loss?


Re: Drill Press

#15

David Barnett

Either way, it'd be horribilis.


Re: Drill Press

#16

George does that make you BuyPolar?