Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Mold in Cabinet HELP please

Posts

Mold in Cabinet HELP please

#1

Mold in Cabinet HELP please

vinny

Hey guys you where all very helpful with my cabinet hinge help so Im hoping I can get some get more good advice. I have a basement apartment in the house I just bought, when doing renovations we noticed there was some mold in only 1 cabinet that was closest to the exterior facing wall in the alleyway. I immediately panicked, my contractor said to spray it down with bleach so the mold spores don't spread when cleaning it which i did, then when it dried i wiped it down with white vinegar and fan dried it, we pull out that cabinet and the three cabinets next to it from the wall to check for mold, no signs of water damage on the walls or mold, he had to open the wall further for a gas line adjustment anyway and again no signs of mold inside the wall. I thought everything was fine and it was due to the apartment not being used for a year and the humidity. Now a week later we open the cabinet door again and once again in the same cabinet some mold started on the right side interior panel. So i went to the store and bought Concrobium mold and mildew cleaner and preventer. I plan on totally spraying down the inside and outside of every cabinet, pulling out all the cabinets and painting the walls behind them with Zisser mold and mildew resistant interior paint, and also buying nansulate clear coat home protect mildew block and clear coat painting the inside of every single cabinet. I am worried though because i definitely do not want to get sued by a tenant and don't want mold in my house. I am baffled by the fact that the walls and fine inside and out and its just in this darn cabinet, i dont want to replace all the cabinets if i don't have to money is tight and they are all in great condition less then 3 years old. Can anyone offer any other advice on this to prevent it from coming back? thanks all

Re: Mold in Cabinet HELP please

#2

I'd stick with bleach even if several applications


Re: Mold in Cabinet HELP please

#3

Re: Mold in Cabinet HELP please

Carol

For mold to grow, it needs air. When you have it killed with bleach or whatever, seal it with shellac - lots of shellac. No air - can't grow.

Re: Mold in Cabinet HELP please

#4

Re: Mold in Cabinet HELP please

GolfSteve in Calgary

Where do you live, Vinny? (this sounds like a line from a gangster movie or Grease :-)

Mold also needs moisture. I suspect this corner of your house is not insulated properly. In the winter condensation is occurring on that cold corner, allowing mold to grow behind the cabinets.

Re: Mold in Cabinet HELP please

#5

Re: Mold in Cabinet

Mark Mandell - Gone Round In New Jersey

Vinny,

In the likelihood that your cabinet carcases are made from ply, surface cleaning with bleach etc. may not be enough because the mold can penetrate the wood layers in the ply, go dormant, and then come back when surface conditions "improve." If that's your scenario, you'd better consider replacing the inside carcase of that one cabinet. Since cabinets are built in modules, you should be able to isolate the effected one and still save both the matching door and any face framing involved without big expense

Remember too, that all molds are not created equal. A bit of mildew, to which some people are very sensitive, is a far cry from the toxic molds that you here about in the media causing houses to be demolished. Mold abatement has become something of a scam with unscrupulous operators playing on the fears and ignorance of the public. You'd do well to research this issue with reliable sources. From everything that you've said, this sounds like something isolated to that cabinet rather than caused by the environment around it.

Re: Mold in Cabinet HELP please

#6

Re: Mold in Cabinet

Barry Irby

Adding to what has been said, Mold needs four things: Air (actually oxygen), warmth, a food source, and water. Oxygen is always present. The warmth is the about the same temps we find comfortable but any where from somewhat below freezing to about 130 degrees F. The food source is anything organic. So to treat it you deprive it of one or more of those things. Can't do much about the oxygen or warmth. That leaves the moisture and the food. You can poison the food by applying some sort of midewcide like Microbane or BoraCare. This might not be good around food and dishes. Zinser does make some excellent Primer (123, I think) and it worked well for me on my bathroom ceiling, but its white.

Changing out the cabinet as Mark suggested would at least assure you of a clean start.

You must have some sort of micro-climate thing going on. I am wondering if that surface is just enough colder than the surrounding surfaces to encourage condensation and thus enough dampness for mold growth? A dehumidifier in the basement might help. Temporarily you could try leaving the cabinet door open.

Re: Mold in Cabinet HELP please

#7

Speaking of Food

Mark Mandell - Gone Round In New Jersey

More than a few molds like the lignin and sugars in wood; that's how we get spalted woods.

Re: Mold in Cabinet HELP please

#8

Rick L

Re: Moldex instead of bleach

Rick L

I've had better luck with Moldex than bleach in the long haul.

http://www.envirocarecorp.com/products/moldex/

Re: Mold in Cabinet HELP please

#9

Re: Mold in Cabinet HELP please

JMOHNIKE

Hire a professional. As an insurance agent in California, I am required to take continuing education classes for my license renewal. One of the classes I take from time to time is on Mold Remediation. Some types of mold can be very toxic to some people, and in some cases has caused death. Every time you sand to remove to mold you spread the spores to other areas where they and grow. It may cost more but you will have a record what was done and by who. Service Master is a company which is used by most if not all of the insurance companies I represent, and they may be in your area. Also for your own protection, you should wear a good mask/filter when working around it. It is not, in my opinion worth taking a chance on, protect yourself let an expert do it.