Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

OT - shimming studs

Posts

OT - shimming studs

#1

OT - shimming studs

Bill Houghton, Sebastopol, CA

I'm in the midst of a remodel on our old (1892-95) house that has included reframing a wall (and will include reframing more walls). The post-war framing on it is slightly larger than current stock - nominal 4" stock is 3-3/4" or so, but variable.

I've held the stock to the inside, and am now facing up to shimming the new studs on the outside to get a fairly flat wall. The trouble is in the variability - one corner post, for instance, ranges from 3/8" to 3/16" wider than the 2x4 face-nailed to it.

On entirely new work, I'd probably just nail it all up and then bring things into line with a power plane. But the old framing in this case is littered with nail heads and such that would wreak havoc with the carbide cutters on my plane.

I'm considering ripping shims to the thinnest dimension needed and making up the difference with a thicker/thinner bead of construction adhesive. Any other or better suggestions?

Re: OT - shimming studs

#2

Re: OT - shimming studs

John Veerkamp

Why shim the front? Laminate a 2X on the side. It will throw your 16" center off in only one place.

Re: OT - shimming studs

#3

I've got it!!!

John in NM

Just finish with plaster instead of drywall - then you won't care if the studs are in a plane or not :b :D

Don't worry, the learning curve with plaster is over-blown.... really, it is :D

Re: OT - shimming studs

#4

BTDT

Mark Mandell - Gone Round In New Jersey

1. Find the "high points" (the worst bellies) in the wall with a chalk line. Consider abrasives (belt or disk sander) to cut them back a bit.

This may be enough to get you by; very few walls are deadnuts flat along their whole length anyway.

If you must,

2. Rip some shimstock to the range of thicknesses you'll need in 1' lengths. I use scrap for this.

3. "String" the wall with mason's line touching the remaining high points at 2' intervals from the floor. Don't forget to check for plumb.

4. Apply shims with PL4000 and a brad gun along the lines which will be where you'll screw the rock.

Goal is to get the studs at the screw lines within 1/8" tolerance as you'll never see the differences when the rock goes on.

Re: OT - shimming studs

#5

Thanks, all

Bill Houghton, Sebastopol, CA

I held the studs to the inside for a couple of reasons, not the outside - so plaster won't save me (and, yes, I know I should learn plaster; but I can do drywall, sort of moderately well, and as always am under the gun to get it done). So what I need is decent nailing surface for 1x10 horizontal shiplapped siding. Since the siding has a 3x8" thick reveal about an inch wide which (I have learned over years of work on this house) is rather delicate, I do want a kind of flat nailing surface.

I had to reframe the entire (short) wall, but for the end "studs" (which were originally 4x4 posts on this converted porch), so I don't want to sister studs on to my new framing.

It seems there's no magic here (whatta surprise!). I may rip my shims to the thickest I need, and get out the belt sander to match the existing wood, although I may phone around to see if I can find the drywall shims suggested on another forum. At least when the belt sander encounters nails, the worst I'll get is a ripped belt; but probably just shiny nailheads.

Re: OT - shimming studs

#6

Don't Discount

Mark Mandell - Gone Round In New Jersey

The usefulness of a 4" disk sander with 24 grit abrasive. Takes wood and nails down pretty quickly ;)

Re: OT - shimming studs

#7

Re: Don't Discount

Jason Waters

I agree that a 4" or even 7" grinder/sander if you got one with a rubber backer and those sanding discs with the hole in the middle that lock on with a nut will really eat some wood (and make some dust).

Sistering is easiest, and shimming works when a wall is straight but leaning. Otherwise if the boards are crooked , shimming is a real pain....

Re: OT - shimming studs

#8

Re: Thanks, all

Dave Bair, Eaton Rapids, MI

I've always seen good builders use a power hand plane; it's very fast and does not create a cloud of dust. If you have little other use for a power plane, a cheap Harbor Freight model might be your best bet.

Re: OT - shimming studs

#9

Nah

Mark Mandell - Gone Round In New Jersey

Dave, All due respect, but with those 19th century nails buried in the studs, he'll be picking high speed steel or carbide planer blade pieces out of his teeth. Hand planers are great for "clean" lumber; not good with foreign objects above the hardness of bullets.

Re: OT - shimming studs

#10

Mark speaks truth

Bill Houghton, Sebastopol, CA

I doubt they're 19th century nails - this particular part of the house is post-World War II remuddling - and, anyway, the 19th century core of the house uses wire nails, not handmade or cut nails; but, regardless, I have no desire to buy new carbide inserts for the Makita planer before time.

It's belt sander time. Ripping shims took very little time, and I'm about to go start applying them...if it doesn't rain on me.

Re: OT - shimming studs

#11

It Rains

Mark Mandell - Gone Round In New Jersey

in Cauliforneeya?

I din't know dat . . . .

Re: OT - shimming studs

#12

If you have an angle grinder...

John in NM

I'll second Mark's suggestion of the 24 grit disk. I use one like this a lot and it really will hog off the wood. Snap a chalk line and cut down to it.

I wasn't entirely serious about the plaster, btw.... it does take a while to learn, and a lot of shoulder muscle. Adding vermiculite (if you can find it) helps a lot, both with the weight and somehow it makes it stickier. Although we grumble a lot about studs not being uniform - and always getting smaller :D - I think we likely have it a lot better than our predecessors with rough sawn stock.

Re: OT - shimming studs

#13

Stuuuds

Mark Mandell - Gone Round In New Jersey

As in 8' 2x4? In spruce by chance?

"EIGHT-FOOT SPRUCE 2X4: A favorite framing member used in vast quantities by handyman-remodeling contractors with the word “Doctor” in their business name. Most commonly installed in the prized “wet/green” state, they are unsurpassed for producing the ever-popular “undulating wall” effect, and are economical in use because they seem to only require a single toenail at top and bottom."

:D

Re: OT - shimming studs

#14

Single toe nail

John in NM

Why use more than one, that will just make it split as it dries and tries to warp :D

Re: OT - shimming studs

#15

Re: Single toe nail

Mark Mandell - Gone Round In New Jersey

That's what she said . . .

Re: OT - shimming studs

#16

a podiatrist's project?


Re: OT - shimming studs

#17

We were supposed to get a shower today

Bill Houghton, Sebastopol, CA

as it was, it just threatened, and misted a little. It's late to still get rain.

But, hey, we even get snow here every decade or so; and we get enough rain every few winters to flood. Not all of California is Malibu. In fact, even though I lived in the upper Midwest several times, the only time I've slid off a road because of ice was here in California, in the Sierra one winter.