Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

After market spliter

Posts

After market spliter

#1

Bob

After market spliter

Bob

I have a Delta UNISAW the splitter and guard are garbage so I would like to get a newer one that does not bend and deform I saw one once that looked lik a shark fin and had a pair of anti-kickback cams that worked from the sheer weight of them. Anyone know where I may get one?

Re: After market spliter

#2

Re: After market spliter

Al Stokka - Cambridge, Iowa

Good morning Bob,

I recall a post from Badger Pond (likely from Mark G.) that Delta sells their splitter two ways; as a part (replacement) and as a kit. One of those was vastly cheaper, but I can't recall which, AND, as "Badger Pond" implies, the post was years ago and Delta may have caught on.

I have the kit number as 78-431, Anti-Kickback, Snap-In Spreader. This info is from October, 2007.

Hopefully, someone with a better memory than mine will post regarding which is cheaper and whether Delta has equalized the prices.

I have this splitter on my saw and it's a joy to use.

Al

Re: After market spliter

#3

Re: Add'l info: After market spliter

Al Stokka - Cambridge, Iowa

Bob,

The splitter carries the name and item number "Biesmeyer 78-431".

Al

Re: After market spliter

#5

Re: Add'l info: After market spliter

Jason Waters

There is the Bisemeyer, and there is the Uniguard splittle. The Bise uses a pin to install and remove, the Uniguard a thumbwheel.

Here is Mark's site, and while it lists a price, don't expect it to be the same now!! It's been over ten years:

http://www.happywoodworking.com/Uniguard.html

Re: After market spliter

#6

Re: After market spliter

Mark Mandell - Gone Round In New Jersey

I've used the Uniguard splitter on my JET cab saw for over 10 years. While it's not a riving knife and must be removed (easy) for non-through cuts, it's done a good-enough job. I took off the silly kick-back pawls. They tend to scratch the wood, and, if your fence is properly adjusted, they're mostly useless anyway IMHO.

Re: After market spliter

#7

Speaking of Mark...

John E. in SC

whatever happened to him? Used to enjoy reading his posts, but haven't seen him here in a long time.

Re: After market spliter

#8

Re: The Shark

mdclor

I have the Sharkguard for my PM66, but without the kickback pawls. It is great for dust collection and is a quality product. However, be prepared to wait for delivery if you order from him. My experience was that delivery took almost 3 months IIRC.

Re: After market spliter

#10

Re: Here is one

Jason Waters

That's the Uniguard splitter, the one I have, and the one shown on Mark's site.

It's a good splitter for the price.

Re: After market spliter

#11

Re: After market spliter

Robby Wright in San Marcos, CA

Bob - I have the old contractor's saw and had the same problem you had. I bought a used Biesemeyer spitter setup and removed the pawls as they were worthless and kept jamming my wood. That worked pretty well, but I wanted something better. I liked the "pull the knob to release" feature, but didn't like the splitter.

I bought replacement splitters for the Shark guard - just the splitters. The link was listed earlier. He made them to my measurements - I asked for a .105 thickness. Great splitters. The setup woriks like a champ.

Re: After market spliter

#12

Bob

Re: After market spliter

Bob

Thank you one and all. Now that I have installed my out feed table I HAVE to get something there for safety I think I will look into the shark and order this week.

Thanks again.

Re: After market spliter

#13

Re: The Shark

Jerry Gibbs

I like the dust pick up feature of the Shark. It is easy to remove for through cuts. The pawls were a waste of money, but not much. Jerry