Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Rocking chair rockers

Posts

Rocking chair rockers

#1

Rocking chair rockers

Rob Scrimgeour

A preliminary search in the archive didn't reveal the info I'm looking for, so I hope that someone can either enlighten me, or point me to a source of info.

I have been asked to replace the badly uneven rockers on a new chair that a friend was given, and I want to cut new rockers from scratch.

What I want to know is this: should the rockers on a rocking chair have a completely spherical curve, or should the curve flatten out slightly on either side of the central part?

Any info would be appreciated.

Rob in Wilderness (S.Africa)

Re: Rocking chair rockers

#2

Re: Rocking chair rockers

Rob Scrimgeour

Just visited Hal Taylor's amazing "Rocking Chair University" and got my answer (spherical) plus a whole lot of other useful info re sizing.

Sorry, I hadn't seen the previous thread from Joseph Mulherin snr, which pointed me in the right direction. Thanks anyway

Rob in Wilderness (S.Africa)

Re: Rocking chair rockers

#3

Re: Rocking chair rockers

Joseph Mulherin Sr.

Rob, am glad someone viewed the website I mentioned about the rocking chair.

I plan on building about 12 of the chairs for family members and a few friends....just got started yesterday on gluing up the back braces.

In building the rockers you have to make 1 1/2"x 3/32" wide lams on the table saw...say about 48".

Copy the form of the old rockers...make a MDF form to match the shape...screw on 1" aluminum angle irons so the lams when glued up and installed onto the forms are alined on one side. Squeeze down you clamps(I used pipe clamps and quick clamps on ends), use Titebond glue, let to setup for at least three hours. Romove them and scrape off the squeeze out glue and them shape the rockers to the form of the old rockers with your ROS or angle grinder flat sander. In making the rockers where they attach to the legs, make some 10" pieces of the lams left over you can cut off after glue up, place them where the legs meet the rockiers, mark the place with pencil, then turn over and glue the pieces to the rockers and use a long screw to attach them. Then shape a smooth transition from leg to rocker, the stain or paint as needed.

Good luck, Joe Mulherin in Indio, CA

Re: Rocking chair rockers

#4

Re: Rocking chair rockers

Rob Scrimgeour

Thanks for all the advice, Joe - I will certainly take it.

(This forum never disappoints!)

Rob in Wilderness (S.Africa)

Re: Rocking chair rockers

#5

Re: Rocking chair rockers

Joseph Mulherin Sr.

You're welcome, Rob. Additional help...the lams should be 9-11 of them thick built up.

Re: Rocking chair rockers

#6

Re: Rocking chair rockers

Joseph Mulherin Sr.

Rob, go to YouTube, type in "Hal Taylor chair" in the upper opening box and up will come the chair and there are maybe 10 videos to watch concerning how to make the rocker/leg attachments block on the band saw.

Re: Rocking chair rockers

#7

Re: Rocking chair rockers

Rob Scrimgeour

Thanks again Joe - I will do so.

Re: Rocking chair rockers

#8

Re: Rocking chair rockers

Joseph Mulherin Sr.

Rob, in making the rockers you want a wood that is hard....like Oak or alder.

They will last longer.

Re: Rocking chair rockers

#9

Re: Rocking chair rockers

Rob Scrimgeour

Thanks Joe - The chair is made of Rhodesian teak, and I intend using the same wood for the rockers - it is plenty hard enough, just hope it will bend OK, but will do a small test first.

Re: Rocking chair rockers

#10

Re: Rocking chair rockers

Carol

Joe, alder is a very soft hardwood, nowhere in the league of oak. FWIW.

Re: Rocking chair rockers

#11

Re: Rocking chair rockers

Joseph Mulherin Sr.

Rob, cut the lams 3/32"x1 1/2"; glue them up 9 to 11 lams per rocker; make a transition piece about 6 lams thick and attach them(epoxy is best) to where the legs of the chair were sitting before. Then attach the rockers to the chair legs using long screws and epoxy. Then you can sand away to your desire to get the desired contour of the rockers. Using the Teak is a very hard wood and should be lasting forever.

Re: Rocking chair rockers

#12

Re: Rocking chair rockers

Joseph Mulherin Sr.

Yes, Carol, I know that. I am going to be using two 3 3/2" lams of oak

underneath the rockers and the rockers will have 11 lams all together

to get the height I need to make the proper contour of the chair rockers.

I am following the design of Hal Taylor's chair very strictly so I obtain

almost a perfect copy of his chair. Today I ran my glued lams on my hand planer

because I do not have a jointer...they came out smooth, then I sawed them

at the required 1 1/2" wide and cut the tag ends where they go into the seat holes.

Next process is to make the seat using Charles Neil's method with the dado blade to scoop out the seat and then use my angle sander to finish the contours...just like I did with the other two chairsw I made earlier this year.

Re: Rocking chair rockers

#13

Re: Interesting video

TomD

Took me a while to refind this. The rocker shape he comes up with was not totally to my taste, but it's interesting anyway.

http://www.youtube.com/watch?v=yDsNlj1oFqo

Re: Rocking chair rockers

#14

Bob

Re: Rocking chair rockers

Bob

I sent away for Hal's DVD set and template, AWESOME he knows his stuff.

Re: Rocking chair rockers

#15

Re: Rocking chair rockers

Joseph Mulherin, Sr.

Hey, Bob, glad someone saw the possibilities of making this wonderful chair.

I know you will be very well pleased. Also, go to You Tube and type in at the upper box "Hal Taylor chair" and up will come several videos you can watch of Hal making the chair parts.

I ordering the plans and the book CD you will be getting the plans for the large, medium, small and children's chairs. I have made the lams for the back braces already for a large chair for my son. Takes some time to get set up, but after making the forms and cutting the lams you can start on making the rockers and back braces. I cut my lams from Alder 1 5/8" x 48", and am using the poplar for the inner braces. He said he uses ash, but poplar is cheaper and will do the job for the springiness of the braces.

Use my email address: joeirish72@aol.com so we two can communicate about our making this chair.

There is a website that would be helpful: "Building the Hal Taylor rocking chair", and "Rocking chair plans". I have them and printed out the pages so I have a folder I can peruse thru in case I have a question to answer instead of returning to the computer and the CD.

Re: Rocking chair rockers

#16

Re: Rocking chair rockers

Joseph Mulherin, Sr.

Bob, go to You Tube and type in "in the workshop by Charles Neil; there you will see him use the dado blade on scooping out the seats. I have done two chairs earlier this year and it does make the job of scooping out much easier.