Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Byrd Shelix Cutterhead for jointer?

Posts

Byrd Shelix Cutterhead for jointer?

#1

Byrd Shelix Cutterhead for jointer?

Sophie

Last week I had to sharpen and replace the knives on my jointer, not really a big deal since I sharpen my own knives but the whole process is just time consuming. Well it just so happens that about that same time I got a sales catalog that has the Shelix cutterheads on sale. So at my age I'm thinking with those carbide tips each having four sharp edges I'd be good for life. But it also got me to thinking how do you align the tables with the cutterhead? So I got out the measuring stuff and the tables are dead flat with each other but the cutterhead itself is .004 low on one end. Now using knives it doesn't matter since you are setting the knives to match the tables but with the Shelix that ain't gonna work. So the question is how do you match the cutters to the tables? Or better yet how do you even measure it?

Sophie

Re: Byrd Shelix Cutterhead for jointer?

#2

Probably be good to give your make and

Keith Newton

model #. On my old tool, everything is adjustable. I'm guessing you are saying that your out feed table is fixed.

You might be able to put some shim stock under the bearings, if that is the case.

Re: Byrd Shelix Cutterhead for jointer?

#3

Re: Probably be good to give your make and

Sophie

Thanks Keith,

It's a 6" Sunhill the exact same one sold by Powerxxxxx of that same time frame just different colors. Also made by Geetech who makes almost all the jointers for most major brands. Everything is adjustable but I just wasn't sure if I could adjust the cutterhead and not have to mess with the tables that are already flat and true. What I'm also after is how do you measure the cutterhead hight since no two cutters are in the same line and they are also at an angle, how do you get a reference point?

Sophie

Re: Byrd Shelix Cutterhead for jointer?

#4

JL

Re: Probably be good to give your make and

JL

You rotate the cutterhead to a reference point. As an example, you pick an outside cutter and then pick an inside cutter - with many cutters (e.g. Byrd Shelix), the cutters are in a spiral configuration. So all you have to do is make sure that the cutters are in the same configuration when you measure them.

As a further example, say you have cutters on the edge at 12 o'clock, 2, 4, 6, 8 and 10 o'clock. As you rotate the cutterhead, the "interior" cutterheads are going to be in a similar orientation. The spirals are very consistent.

Re: Byrd Shelix Cutterhead for jointer?

#5

Re: Probably be good to give your make and

Keith Newton

Well, you only need to worry about one tooth on one end at a time, and everything in the head ought to take care of itself.

I have a dial indicator mounted in a fixture which I zero on the out feed table, then move to each end of a blade as I set them, not worrying about the middle.

If you don't have access to one of these, you can just use a straight piece of wood, resting on the outfeed, then rotate the blade, trying to keep the height, to where the board only traverses about 1/8" as the tooth moves under it.

Re: Byrd Shelix Cutterhead for jointer?

#6

Re: Byrd Shelix Cutterhead for jointer?

Larry Clinton At Frankfort, (Central) Indiana

Sophie, I have the Grizzly 8" jointer with the segmented carbide head. I used an indicator with a flat tip to set my outfeed table. Just picked up the high points on the inside and outside cutters. I have the Byrd head in my 20" stationary planer - really can't tell any difference in the finish between the two brands. I will say I would never go back to a blade style head. The inserts can be rotated 4 times before replacement and there is NO setup. All you have to do is make sure there is no derbies under the insert when you rotate it and that it seats properly. They also stay sharp for a long, long time compared to HSS, and if you do chip one or even a row, you can drop in just those new ones. You may quit trying to read the grain when feeding as it doesn't seem to matter. I actually fed an assembled oak paneled door through the planer (someone put the panel in backward and it was raised above the frame, duh), I planed it till I touched the frame without any tear-out. I did rotate my planer inserts after about 4 years of hobby use (several hundred bf of white oak, locust, cherry, walnut, cedar and various other woods). If you feel the need for a new tool (who doesn't) you may want to look at the Griz's jointer offerings in 8".

Re: Byrd Shelix Cutterhead for jointer?

#7

I would use reference edge same as normal knives

Dave Paine

I have a 6in Delta jointer with conventional knives.

I now use a 36in straight edge from Lee Valley to set knives.

This is about 1/4in thick so stands up by itself.

I place the straight edge on the outfeed table and adjust one side of the knife to just touch the edge as I rotate the cutterhead. I actually watch to slightly lift the edge then back off 1/4 turn then sneak back until I can feel contact, but the edge does not move or lift.

I do this on the other side, then go back and check the first side.

I would use the same technique with a Shelix. Each cutter is meant to present the same profile. I would select a cutter at or near the end, and its equivalent at the other end.

I was pleasantly surprised when I used the straight edge. The jointer sounded much quieter, just running without stock. It was also quieter when pushing some stock through.

I highly recommend a good steel straight edge. Previously I used a level, but I think it was too wide. I am now sold on the steel straight edge.

Re: Byrd Shelix Cutterhead for jointer?

#8

Thanks guys I think I got it.