Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

How Does This Work?

Posts

How Does This Work?

#1

How Does This Work?

AZ in Colorado Springs

I volunteer at the wood skills center (aka "the woodshop") at the US Air Force Academy. It is connected (physically) to the framing shop and the arts and crafts center. Someone (don't know who and can't find out who it was) donated the item pictured below and left it in the arts and crafts center.

The text in the lower right box says "universal radial fence saw top" and "pat. pending." There is no manufacturer or model number.

The back is flat, except for a few bolts that poke through (which hold the jig arms and guides in place and a metal plate that strengthens this same are where the bolts come through). This jig will not lie flat on the table in front of the RAS, and there seems to be no mounting points. Also, we did not get any bits of hardware or brackets with this jig -- just what's in the photo.

It seems that this is an angle jig, and an older one. (It shows no signs of ever having been used.) There are no stops or detents and those seem to come on every angle jig or miter guage these days. (I didn't think to measure length and width; if that's important I can measure it tomorrow. But I'd guess it's about 40 or 44 inches in each direction.)

So my question is "how does this jig work?" In case it makes a difference. the RAS is a Rockwell model 16-RAS, and looks to have been built during the Eisenhower administration.

Thanks

AZ


Re: How Does This Work?

#2

Re: How Does This Work?

Stuart Johnson

A guess.. The straight edge goes against the back fence and the cut out allows you to get closer to the saw. Set the angle on the thing and then swing the saw so the blade touches the guide. The size probably give finer adjustment.

Re: How Does This Work?

#3

Re: How Does This Work?

Dave Paine

I am also making a guess. The board marking infers this is some type of angle jig, likely so that the carriage arm of the RAS did not need to move. One reason may be that RAS's are famous for not returning to the exact location when the carriage is moved, so may need re-calibrating. Another reason is that if you move the carriage 45 deg to one side, there is little cross cut capacity left.

I think this jig may have been intended to be more accurate, to avoid moving the carriage, and to provide greater cross cut capacity.

I think some wood sub fence would have been in stalled on the L pieces. Perhaps the sub fence was intended to touch the board.

The arms must have installed into a special mounting bracket which was attached to the RAS column or some other anchor point on the frame. Then adjusted to be parallel to each other and then locked in place with the thumb screws. I would expect the longer arm would go on the side with the RAS motor and the shorter arm the side with the blade.

Interesting find.

Re: How Does This Work?

#4

Only the Air Force . . .

steve mackay

. . . would buy such a thing. :D My ARMY, on the other hand, would issue a hacksaw and say "deal with it". ;)

Re: How Does This Work?

#5

Re: Only the Air Force . . .

AZ in Colorado Springs

It was a donation ... or perhaps an "abandonment" (if there is such a word). Not a purchase.

It seems to me that it's like a crosscut sled, except that it would be stationary (a table top unto itself). Did people install "miter tabletops" on their RASs?

Re: How Does This Work?

#6

Jason Roehl in Lafayette, IN

Re: How Does This Work?

Jason Roehl in Lafayette, IN

I suspect that the cut-out portion goes against the RAS fence, with the centerline being used to align to the blade, then the angle iron piece on the appropriate side is used as a fence for the board to be mitered since an RAS blade pushes a board towards the back of the saw as it cuts.

Jason

Re: How Does This Work?

#7

Thanks for the replies

AZ in Colorado Springs

I don't think we're much closer to getting it installed, but I appreciate your thoughts. If we ever get it into operation, I'll post a photo.

Cheers