Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Cleaning table saw top

Posts

Cleaning table saw top

#1

Cleaning table saw top

Lynn Reedy

Hello from Soddy Daisy Tenn.,

I need to clean my table saw top. I have heard that wd-40

and a plastic scrub pad are best for this job. After that a good coat

of past wax either furniture or car wax should do. Any suggestions?

Thanks,

Reedy

Re: Cleaning table saw top

#2

Re: Cleaning table saw top

Dave Paine

You do not state if you have rust, or just the grime which can build up over time.

If you have rust, then a product like Boeshield or Autosol can remove the rust. Both are available at Lee Valley.

If you have grime, then using 600 grit wet/dry abrashive with some oil for the "wet" will do wonders. The oil will act as the fluid and will mean no residual moisture. I happened to have used this technique only a few days ago on two rust spots on my disc sander. The spots felt "rough" but after a few seconds with 600 grit and oil they were smooth with no rust.

Re: Cleaning table saw top

#3

Re: Cleaning table saw top

Dick Coers

If it's heavy rust, I like to use a single edge razor blade in a handle and push it through the rust. Then WD40 and Scotch bright.

Re: Cleaning table saw top

#4

avoid silicone containing wax

Bill Tindall

Given the problems that even 1 molecule of silicon seems to have on finishing I would not use any wax that contains silicone. I make my own. Carnuba plus xylene.

Steel wool and wax makes a decent cleaning procedure.

Re: Cleaning table saw top

#5

Re: avoid silicone containing wax

Thomas S Stockton

I do pretty much the same as what Bill does. It doesn't matter to me if my tops are shiny, what is important is that they slide smoothly and wax does this really well and is cheap. I won't sand my tops I see no reason to go that far and stains don't bother me at all. So the most aggressive I get is 0000 steel wool.

Tom

Re: Cleaning table saw top

#6

Me Too

David Yoho

I'm with Thomas in this matter. I don't care about the few stains my top has; they're character in my eyes and shows frequent use, which is what a working saw should reveal.

I'm more interested in how well the stock moves over its surface. To that end, I simply apply a coat of Johnson's Wax when necessary.

If I'm cleaning or removing a bit of surface rust I go with WD-40 and a gray Scotch-Brite pad and then apply the wax. The WD-40 rids the surface of moisture while the solvent and the pad loosen and remove grim and light rust. I never shoot for a like-new look because it won't stay that way around here!

Re: Cleaning table saw top

#7

JL

Re: Cleaning table saw top

JL

This is going to sound weird - but so be it.

For light rust and discoloration:

Take a piece of heavy duty aluminum foil (wear gloves) and fold it so the "dull side" is out. Put a couple of drops of water on the table top. Scrub with the foil. Repeat as needed.

The aluminum oxide on the exterior of the foil acts as a light abrasive. The water acts as a lubricant. You also set up enough of a chemical reaction between the rust and the aluminum oxide to help things along a little bit.

For heavier stuff, I use sandpaper - either silicon carbide wet/dry or heavier duty aluminum oxide. I sometimes use abrasive pads and WD-40 or mineral spirits.

Re: Cleaning table saw top

#8

Re: Cleaning table saw top

steve mackay

Scrapeing scares me on anything. Just mineral spirits. A bit of steel wool if its REALLY on there. Scrub, scrub, scrub, then a machined surface's best-est friend : good ol' Johnson's Paste Wax.

Re: Cleaning table saw top

#9

Boeshield T9 and Rust off is all thai is needed

del schisler

sears store's has this product now. With these you will not have to scrub very little I wouldn't use any oil on my saw unless you get it all off. Finish's don't like oil or wax. The wd-40 may be ok but i don't use this stuff. The WD stand's for water displacement that was what it was made for? If their is some rust the rust off will get it to looking like new. and the T-9 will keep it looking that way. These product's were mfd. by boeing aircraft co. Works for me i haven't had any rust on any of my tool's i live in eastern florida 10 miles from the ocean. my 2 cents

Re: Cleaning table saw top

#10

Rusty Table Tops

George Colonel's Workshop-Havertown PA

Good Afternoon Lynn,

I hate rust or blems on my table and band saw surfaces and use a ROM w/grits as heavy as 120. Mostly 220/320 is responsive. Then paste wax. Mine are tools used daily, not museum pieces, so I don't fuss.

George